A311D 硬件启动时打印消息,为什么只是在uboot的时候显示了logo，内核启动时就什么...
[复制链接]
G12B:BL:6e7c85:2a3b91;FEAT:E0F83180:402000;POC:F;RCY:0;EMMC:0;READ:0;0.
l2_stage_init 0x01
bl2_stage_init 0x81
hw id: 0x0000 - pwm id 0x01
bl2_stage_init 0xc1
bl2_stage_init 0x02
L0:00000000
L1:20000703
L2:00008067
L3:14000000
B2:00402000
B1:e0f83180
TE: 220130
BL2 Built : 15:22:05, Aug 28 2019. g12b g1bf2b53 - luan.yuan@droid15-sz
Board ID = 8
Set A53 clk to 24M
Set A73 clk to 24M
Set clk81 to 24M
A53 clk: 1200 MHz
A73 clk: 1200 MHz
CLK81: 166.6M
smccc: 0003a3bf
eMMC boot @ 0
sw8 s
DDR driver_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 15:22:01
board id: 8
Load FIP HDR from eMMC, src: 0x00010200, des: 0xfffd0000, size: 0x00004000, part: 0
fw parse done
Load ddrfw from eMMC, src: 0x00060200, des: 0xfffd0000, size: 0x0000c000, part: 0
Load ddrfw from eMMC, src: 0x00038200, des: 0xfffd0000, size: 0x00004000, part: 0
PIEI prepare done
fastboot data load
00000000
emmc switch 1 ok
ddr saved addr:00016000
Load ddr parameter from eMMC, src: 0x02c00000, des: 0xfffd0000, size: 0x00001000, part: 0
00000000
emmc switch 0 ok
fastboot data verify
verify result: 265
Cfg max: 4, cur: 1. Board id: 255. Force loop cfg
LPDDR4 probe
ddr clk to 1608MHz
Load ddrfw from eMMC, src: 0x0003c200, des: 0xfffd0000, size: 0x0000c000, part: 0
dmc_version 0001
Check phy result
INFO : End of CA training
INFO : End of initialization
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read enable training
INFO : End of fine write leveling
INFO : End of Write leveling coarse delay
INFO : Training has run successfully!
Check phy result
INFO : End of initialization
INFO : End of read dq deskew training
INFO : End of MPR read delay center optimization
INFO : End of write delay center optimization
INFO : End of read delay center optimization
INFO : End of max read latency training
INFO : Training has run successfully!
1D training succeed
Load ddrfw from eMMC, src: 0x00048200, des: 0xfffd0000, size: 0x0000c000, part: 0
Check phy result
INFO : End of initialization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D read delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : End of 2D write delay Voltage center optimization
INFO : Training has run successfully!
channel==0
RxClkDly_Margin_A0==87 ps 9
TxDqDly_Margin_A0==106 ps 11
RxClkDly_Margin_A1==87 ps 9
TxDqDly_Margin_A1==106 ps 11
TrainedVREFDQ_A0==27
TrainedVREFDQ_A1==27
VrefDac_Margin_A0==30
DeviceVref_Margin_A0==27
VrefDac_Margin_A1==30
DeviceVref_Margin_A1==27
channel==1
RxClkDly_Margin_A0==106 ps 11
TxDqDly_Margin_A0==106 ps 11
RxClkDly_Margin_A1==97 ps 10
TxDqDly_Margin_A1==106 ps 11
TrainedVREFDQ_A0==26
TrainedVREFDQ_A1==26
VrefDac_Margin_A0==27
DeviceVref_Margin_A0==25
VrefDac_Margin_A1==26
DeviceVref_Margin_A1==25
dwc_ddrphy_apb_wr((0<<20)|(2<<16)|(0<<12)|(0xb0):0004
soc_vref_reg_value 0x 00000025 00000026 00000028 00000026 00000026 00000026 00000026 00000026 00000027 00000025 00000024 00000026 00000026 00000026 00000026 00000026 00000027 00000027 00000026 00000026 00000025 00000026 00000026 00000027 00000027 00000026 00000026 00000027 00000026 00000027 00000027 00000027 dram_vref_reg_value 0x 00000013
2D training succeed
aml_ddr_fw_vesion: LPDDR4_PHY_V_0_1_18 build time: Aug 28 2019 13:54:19
auto size-- 65535DDR cs0 size: 2048MB
DDR cs1 size: 2048MB
DMC_DDR_CTRL: 00e00024DDR size: 3928MB
cs0 DataBus test pass
cs1 DataBus test pass
cs0 AddrBus test pass
cs1 AddrBus test pass
100bdlr_step_size ps== 393
result report
boot times 0Enable ddr reg access
00000000
emmc switch 3 ok
Authentication key not yet programmed
get rpmb counter error 0x00000007
00000000
emmc switch 0 ok
Load FIP HDR from eMMC, src: 0x00010200, des: 0x01700000, size: 0x00004000, part: 0
Load BL3X from eMMC, src: 0x00078200, des: 0x01768000, size: 0x000d0000, part: 0
0.0;M3 CHK:0;cm4_sp_mode 0
MVN_1=0x00000000
MVN_2=0x00000000
[Image: g12b_v1.1.3390-6ac5299 2019-09-26 14:10:05 luan.yuan@droid15-sz]
OPS=0x10
ring efuse init
chipver efuse init
29 0b 10 00 01 28 0e 00 00 0c 35 38 47 47 52 50
[0.018961 Inits done]
secure task start!
high task start!
low task start!
run into bl31
NOTICE: BL31: v1.3(release):4fc40b1
NOTICE: BL31: Built : 15:58:17, May 22 2019
NOTICE: BL31: G12A normal boot!
NOTICE: BL31: BL33 decompress pass
ERROR: Error initializing runtime service opteed_fast
U-Boot 2015.01 (Aug 26 2020 - 09:24:47)
DRAM: 3.8 GiB
Relocation Offset is: d6e45000
spi_post_bind(spifc): req_seq = 0
register usb cfg[0][1] = 00000000d7f399b8
aml_i2c_init_port init regs for 0
MMC: aml_priv->desc_buf = 0x00000000d3e35a70
aml_priv->desc_buf = 0x00000000d3e37db0
SDIO Port B: 0, SDIO Port C: 1
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x3, tx-dly 0, clock 400000
emmc/sd response timeout, cmd8, status=0x3ff2800
emmc/sd response timeout, cmd55, status=0x3ff2800
co-phase 0x3, tx-dly 0, clock 400000
co-phase 0x1, tx-dly 0, clock 40000000
aml_sd_retry_refix[983]:delay = 0x0,gadjust =0x2000
[mmc_startup] mmc refix success
init_part() 297: PART_TYPE_AML
[mmc_init] mmc init success
start dts,buffer=00000000d3e3a620,dt_addr=00000000d3e3a620
get_partition_from_dts() 91: ret 0
parts: 3
00: logo 0000000000800000 1
01: ramdisk 0000000002000000 1
02: rootfs ffffffffffffffff 4
init_part() 297: PART_TYPE_AML
eMMC/TSD partition table have been checked OK!
crc32_s:0x1577dad == storage crc_pattern:0x1577dad!!!
crc32_s:0xee152b83 == storage crc_pattern:0xee152b83!!!
crc32_s:0x79f50f07 == storage crc_pattern:0x79f50f07!!!
mmc env offset: 0x6c00000
In: serial
Out: serial
Err: serial
reboot_mode=cold_boot
[store]To run cmd[emmc dtb_read 0x1000000 0x40000]
_verify_dtb_checksum()-3477: calc 86c14a96, store 86c14a96
_verify_dtb_checksum()-3477: calc 86c14a96, store 86c14a96
dtb_read()-3694: total valid 2
update_old_dtb()-3675: do nothing
aml_i2c_init_port init regs for 0
fusb302_init: Device ID: 0x91
CC connected in 0 as UFP
fusb302 detect chip.port_num = 0
amlkey_init() enter!
[EFUSE_MSG]keynum is 1
vpu: clk_level in dts: 7
vpu: vpu_power_on
vpu: set clk: 666667000Hz, readback: 666666667Hz(0x100)
vpu: vpu_module_init_config
vpp: vpp_init
vpp: vpp osd2 matrix rgb2yuv..............
cvbs: cpuid:0x29
LCD_RESET PIN: 0
lcd: detect mode: tablet, key_valid: 0
lcd: detect lcd_clk_path: 1
lcd: load config from dts
lcd: pinctrl_version: 2
lcd: use panel_type=lcd_0
lcd: bl: pinctrl_version: 2
lcd: bl: name: backlight_pwm, method: 1
lcd: bl: aml_bl_power_ctrl: 0
Net: dwmac.ff3f0000
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
MACADDR:02:00:00:0e:28:01(from chipid)
upgrade_step=2
reboot_mode:::: cold_boot
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
mac address: c8:63:14:70:c9:c7
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
edid preferred_mode is <NULL>[0]
hdr mode is 0
dv mode is ver:0 len: 0
hdr10+ mode is 0
HDMI cable is NOT connected
hpd_state=0
[OSD]load fb addr from dts:/meson-fb
[OSD]set initrd_high: 0x7f800000
[OSD]fb_addr for logo: 0x7f800000
[OSD]load fb addr from dts:/meson-fb
[OSD]fb_addr for logo: 0x7f800000
[OSD]VPP_OFIFO_SIZE:0xfff01fff
[CANVAS]canvas init
[CANVAS]addr=0x7f800000 width=5760, height=2160
card out
** Bad device mmc 0 **
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
750056 bytes read in 52 ms (13.8 MiB/s)
[OSD]osd_hw.free_dst_data: 0,1023,0,599
[OSD]osd1_update_disp_freescale_enable
cvbs: outputmode[panel] is invalid
hdmitx: outputmode[panel] is invalid
vpp: vpp_matrix_update: 0
vpp: g12a/b post2(bit12) matrix: YUV limit -> RGB ..............
lcd: enable: TS050, mipi, 1024x600@60.0Hz
lcd: tablet driver init(ver 20180718): mipi
lcd: lcd_pll_wait_lock: pll_lock=1, wait_loop=1
vpp: vpp_init_lcd_gamma_table
lcd: error: gpio: wrong name GPIO_EXPANinvalid
lcd: error: gpio: wrong name GPIO_EXPANGPIO_EXPANinvalid
lcd: error: gpio: wrong name GPIO_EXPANGPIO_EXPANinvalid
lcd: pixel_clk = 47.250MHz, bit_rate = 283.500MHz, lanebyteclk = 35.437MHz
lcd: Waiting STOP STATE LANE
lcd: dsi init on
lcd: bl: set level: 100, last level: 0
lcd: bl: aml_bl_power_ctrl: 1
lcd: clear mute
vpp: Rx hdr_info.hdr_sup_eotf_smpte_st_2084 = 0
amlkey_init() enter!
amlkey_init() 71: already init!
[EFUSE_MSG]keynum is 1
[KM]Error:f[key_manage_query_size]L515:key[usid] not programed yet
mac address: c8:63:14:70:c9:c7
[KM]Error:f[key_manage_query_size]L515:key[deviceid] not programed yet
gpio: pin GPIOAO_7 (gpio 7) value is 1
saradc: 0x28b, hw_ver: 0x32 (VIM3.V12)
Product checking: pass! Hardware version: VIM3.V12
normal power on
boot wol: disable
port mode is pcie
Hit Enter or space or Ctrl+C key to stop autoboot -- : 0
pll tsensor avg: 0x2120, u_efuse: 0x80e1
temp1: 44
ddr tsensor avg: 0x217d, u_efuse: 0x8136
temp2: 46
device cool done
cfgload: start ...
cfgload: reading /boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot.ini or empty file on mmc 0:1
cfgload: reading /boot/boot.ini from mmc 0:1 ...
card out
** Bad device mmc 0 **
cfgload: no /boot/boot.ini or empty file on mmc 0:1
cfgload: reading /boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:1 ...
Failed to mount ext2 filesystem...
** Unrecognized filesystem type **
cfgload: no /boot/boot.ini or empty file on mmc 1:1
cfgload: reading /boot/boot.ini from mmc 1:5 ...
9263 bytes read in 4 ms (2.2 MiB/s)
cfgload: applying boot.ini...
[#] Script a:d3e3be50 l:9243 c:0 s:0 - run
Starting boot.ini...
saradc: 0x28b, hw_ver: 0x32 (VIM3.V12)
uboot type: vendor
Scanning mmc 0:1...
card out
** Bad device mmc 0 **
Scanning mmc 0:5...
card out
** Bad device mmc 0 **
Scanning mmc 1:1...
** Unrecognized filesystem type **
Scanning mmc 1:5...
8472403 bytes read in 245 ms (33 MiB/s)
28901888 bytes read in 818 ms (33.7 MiB/s)
80471 bytes read in 8 ms (9.6 MiB/s)
3617 bytes read in 5 ms (706.1 KiB/s)
Import env.txt
Can not get u-boot part UUID, set to NULL
Booting legacy kernel...
port mode is pcie
Apply dtbo uart3
225 bytes read in 8 ms (27.3 KiB/s)
Apply dtbo pwm_f
345 bytes read in 7 ms (47.9 KiB/s)
Apply dtbo i2c3
223 bytes read in 7 ms (30.3 KiB/s)
Apply dtbo os08a10
1072 bytes read in 8 ms (130.9 KiB/s)
HDMI: Autodetect: 1080p60hz
## Loading init Ramdisk from Legacy Image at 13000000 ...
Image Name: uInitrd
Image Type: AArch64 Linux RAMDisk Image (gzip compressed)
Data Size: 8472339 Bytes = 8.1 MiB
Load Address: 00000000
Entry Point: 00000000
Verifying Checksum ... OK
load dtb from 0x1000000 ......
## Flattened Device Tree blob at 01000000
Booting using the fdt blob at 0x1000000
reserving fdt memory region: addr=1000000 size=14000
Loading Ramdisk to 7efeb000, end 7f7ff713 ... OK
Loading Device Tree to 000000001ffe9000, end 000000001fffffff ... OK
Starting kernel ...
uboot time: 5234088 us
[ 0.000000@0] Booting Linux on physical CPU 0x0
[ 0.000000@0] Linux version 4.9.232 (root@ubuntu) (gcc version 7.3.1 20180425 [linaro-7.3-2018.05 revision d29120a424ecfbc167ef90065c0eeb7f91977701] (Linaro GCC 7.3-2018.05) ) #8 SMP PREEMPT Tue Aug 25 22:14:41 PDT 2020
[ 0.000000@0] Boot CPU: AArch64 Processor [410fd034]
[ 0.000000@0] Machine model: Khadas VIM3
[ 0.000000@0] efi: Getting EFI parameters from FDT:
[ 0.000000@0] efi: UEFI not found.
[ 0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x0000000005000000, end:0x0000000005400000, len:4 MiB
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x0000000005000000, size 4 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,secmon, compatible id shared-dma-pool
[ 0.000000@0] OF: reserved mem: __reserved_mem_alloc_size, start:0x000000007f800000, end:0x0000000080000000, len:8 MiB
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x000000007f800000, size 8 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,meson-fb, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000e5800000, size 128 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,ion-dev, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000e3000000, size 40 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,di_cma, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created DMA memory pool at 0x00000000e3000000, size 0 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,ppmgr, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000cfc00000, size 308 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_cma, compatible id shared-dma-pool
[ 0.000000@0] OF: reserved mem: initialized node linux,codec_mm_reserved, compatible id amlogic, codec-mm-reserved
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000cbc00000, size 64 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,vdin0_cma, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000c7c00000, size 64 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,vdin1_cma, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000c6c00000, size 16 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,galcore, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a7c00000, size 496 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,isp_cma, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a4c00000, size 48 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,adapt_cma, compatible id shared-dma-pool
[ 0.000000@0] Reserved memory: created CMA memory pool at 0x00000000a0c00000, size 64 MiB
[ 0.000000@0] OF: reserved mem: initialized node linux,gdc_cma, compatible id shared-dma-pool
[ 0.000000@0] cma: Reserved 8 MiB at 0x00000000a0400000
[ 0.000000@0] psci: probing for conduit method from DT.
[ 0.000000@0] psci: PSCIv1.0 detected in firmware.
[ 0.000000@0] psci: Using standard PSCI v0.2 function IDs
[ 0.000000@0] psci: MIGRATE_INFO_TYPE not supported.
[ 0.000000@0] psci: SMC Calling Convention v1.1
[ 0.000000@0] percpu: Embedded 25 pages/cpu s64920 r8192 d29288 u102400
[ 0.000000@0] Detected VIPT I-cache on CPU0
[ 0.000000@0] CPU features: enabling workaround for ARM erratum 845719
[ 0.000000@0] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 957600
[ 0.000000@0] Kernel command line: root=UUID=8f600e4e-c55d-4e5c-92d6-83a06c3a0099 rootfstype=ext4 rootflags=data=writeback rw ubootpart=NULL console=ttyS0,115200n8 console=tty0 no_console_suspend consoleblank=0 loglevel=7 logo=osd0,loaded,0x3d800000,panel vout=panel,enable hdmimode=1080p60hz fsck.repair=yes net.ifnames=0 wol_enable=0 max_freq_a53=1800 max_freq_a73=2208 jtag=disable mac=c8:63:14:70:c9:c7 fan=auto khadas_board=VIM3 hwver=VIM3.V12 coherent_pool=2M reboot_mode=cold_boot imagetype=EMMC uboottype=vendor
[ 0.000000@0] fb: osd0
[ 0.000000@0] fb: loaded
[ 0.000000@0] fb: 0x3d800000
[ 0.000000@0] fb: panel
[ 0.000000@0] vout: panel
[ 0.000000@0] vout: enable: 1
[ 0.000000@0] vout: get hdmimode: 1080p60hz
[ 0.000000@0] init_wol_state, wol_enable=0
[ 0.000000@0] max cpufreq of cluster0 : 1800MHz
[ 0.000000@0] max cpufreq of cluster1 : 2208MHz
[ 0.000000@0] jtag: jtag select disable
[ 0.000000@0] PID hash table entries: 4096 (order: 3, 32768 bytes)
[ 0.000000@0] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
[ 0.000000@0] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.000000@0] Memory: 2505364K/3891200K available (14844K kernel code, 1856K rwdata, 5948K rodata, 5504K init, 1491K bss, 107884K reserved, 1277952K cma-reserved)
[ 0.000000@0] Virtual kernel memory layout:
[ 0.000000@0] modules : 0xffffff8000000000 - 0xffffff8008000000 ( 128 MB)
[ 0.000000@0] vmalloc : 0xffffff8008000000 - 0xffffffbebfff0000 ( 250 GB)
[ 0.000000@0] .text : 0xffffff8009080000 - 0xffffff8009f00000 ( 14848 KB)
[ 0.000000@0] .rodata : 0xffffff8009f00000 - 0xffffff800a4e0000 ( 6016 KB)
[ 0.000000@0] .init : 0xffffff800a4e0000 - 0xffffff800aa40000 ( 5504 KB)
[ 0.000000@0] .data : 0xffffff800aa40000 - 0xffffff800ac10200 ( 1857 KB)
[ 0.000000@0] .bss : 0xffffff800ac10200 - 0xffffff800ad84ea4 ( 1492 KB)
[ 0.000000@0] fixed : 0xffffffbefe7fd000 - 0xffffffbefec00000 ( 4108 KB)
[ 0.000000@0] PCI I/O : 0xffffffbefee00000 - 0xffffffbeffe00000 ( 16 MB)
[ 0.000000@0] vmemmap : 0xffffffbf00000000 - 0xffffffc000000000 ( 4 GB maximum)
[ 0.000000@0] 0xffffffbf00000000 - 0xffffffbf03b60000 ( 59 MB actual)
[ 0.000000@0] memory : 0xffffffc000000000 - 0xffffffc0ed800000 ( 3800 MB)
[ 0.000000@0] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=6, Nodes=1
[ 0.000000@0] Preemptible hierarchical RCU implementation.
[ 0.000000@0] Build-time adjustment of leaf fanout to 64.
[ 0.000000@0] RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=6.
[ 0.000000@0] RCU: Adjusting geometry for rcu_fanout_leaf=64, nr_cpu_ids=6
[ 0.000000@0] NR_IRQS:64 nr_irqs:64 0
[ 0.000000@0] irq_meson_gpio: 100 to 8 gpio interrupt mux initialized
[ 0.000000@0] g12a_aoclkc_init: register ao clk ok!
[ 0.000000@0] Meson chip version = RevB (29:B - 10:0)
[ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[ 0.000000@0] meson_g12a_sdemmc_init: register amlogic sdemmc clk
[ 0.000000@0] meson_g12a_gpu_init: register meson gpu clk
[ 0.000000@0] meson_g12a_media_init: register meson media clk
[ 0.000000@0] meson_g12a_misc_init: register amlogic g12a misc clks
[ 0.000000@0] meson_g12a_misc_init: done.
[ 0.000000@0] g12a_clkc_init initialization complete
[ 0.000000@0] arm_arch_timer: Architected cp15 timer(s) running at 24.00MHz (phys).
[ 0.000000@0] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[ 0.000004@0] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[ 0.000045@0] meson_bc_timer: mclk->mux_reg =ffffff800800c190,mclk->reg =ffffff800800e194
[ 0.000729@0] Console: colour dummy device 80x25
[ 0.002325@0] console [tty0] enabled
[ 0.002350@0] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=96000)
[ 0.002382@0] pid_max: default: 32768 minimum: 301
[ 0.002431@0] thread_stack_cache_init, vmap:ffffffc09b87a780, bitmap:ffffffc09b874000, cache page:9b880
[ 0.002464@0] thread_stack_cache_init, allocation vm area:ffffffc09b83b780, addr:ffffff8020000000, size:20001000
[ 0.002492@0] cpu 0, vmap_stack:[ffffffc0a02fcae0-ffffffc0a0300ad0]
[ 0.002510@0] cpu 0, irq_stack: [ffffffc0a02f3060-ffffffc0a02f7050]
[ 0.002527@0] cpu 1, vmap_stack:[ffffffc0a0315ae0-ffffffc0a0319ad0]
[ 0.002544@0] cpu 1, irq_stack: [ffffffc0a030c060-ffffffc0a0310050]
[ 0.002562@0] cpu 2, vmap_stack:[ffffffc0a032eae0-ffffffc0a0332ad0]
[ 0.002579@0] cpu 2, irq_stack: [ffffffc0a0325060-ffffffc0a0329050]
[ 0.002596@0] cpu 3, vmap_stack:[ffffffc0a0347ae0-ffffffc0a034bad0]
[ 0.002613@0] cpu 3, irq_stack: [ffffffc0a033e060-ffffffc0a0342050]
[ 0.002631@0] cpu 4, vmap_stack:[ffffffc0a0360ae0-ffffffc0a0364ad0]
[ 0.002648@0] cpu 4, irq_stack: [ffffffc0a0357060-ffffffc0a035b050]
[ 0.002665@0] cpu 5, vmap_stack:[ffffffc0a0379ae0-ffffffc0a037dad0]
[ 0.002682@0] cpu 5, irq_stack: [ffffffc0a0370060-ffffffc0a0374050]
[ 0.002760@0] Security Framework initialized
[ 0.002780@0] SELinux: Initializing.
[ 0.002867@0] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.002888@0] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes)
[ 0.003571@0] ftrace: allocating 48069 entries in 188 pages
[ 0.091827@0] sched-energy: Sched-energy-costs installed from DT
[ 0.091860@0] CPU0: update cpu_capacity 631
[ 0.091885@0] ASID allocator initialised with 65536 entries
[ 0.151594@0] secmon: clear_range:5100000 200000
[ 0.152427@0] EFI services will not be available.
[ 0.200028@1] Detected VIPT I-cache on CPU1
[ 0.200081@1] CPU1: update cpu_capacity 631
[ 0.200083@1] CPU1: Booted secondary processor [410fd034]
[ 0.232571@2] Detected VIPT I-cache on CPU2
[ 0.232615@2] CPU2: update cpu_capacity 1192
[ 0.232617@2] CPU2: Booted secondary processor [410fd092]
[ 0.264130@3] Detected VIPT I-cache on CPU3
[ 0.264153@3] CPU3: update cpu_capacity 1192
[ 0.264155@3] CPU3: Booted secondary processor [410fd092]
[ 0.296223@4] Detected VIPT I-cache on CPU4
[ 0.296246@4] CPU4: update cpu_capacity 1192
[ 0.296248@4] CPU4: Booted secondary processor [410fd092]
[ 0.328307@5] Detected VIPT I-cache on CPU5
[ 0.328329@5] CPU5: update cpu_capacity 1192
[ 0.328331@5] CPU5: Booted secondary processor [410fd092]
[ 0.328419@0] Brought up 6 CPUs
[ 0.328635@0] SMP: Total of 6 processors activated.
[ 0.328657@0] CPU features: detected feature: 32-bit EL0 Support
[ 0.328803@0] CPU: All CPU(s) started at EL2
[ 0.328858@0] alternatives: patching kernel code
[ 0.330926@0] addr:ffffff80200c3e16 is in kernel, size fix 4096->10, data:mode=0755
[ 0.331120@2] devtmpfs: initialized
[ 0.345670@1] DMI not present or invalid.
[ 0.346073@1] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.346120@1] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.346372@1] pinctrl core: initialized pinctrl subsystem
[ 0.347449@1] NET: Registered protocol family 16
[ 0.349454@1] schedtune: init normalization constants...
[ 0.349488@1] schedtune: CLUSTER[0-1] min_pwr: 0 max_pwr: 42
[ 0.349510@1] schedtune: CPU[0] min_pwr: 0 max_pwr: 279
[ 0.349531@1] schedtune: CPU[1] min_pwr: 0 max_pwr: 279
[ 0.349552@1] schedtune: CLUSTER[2-5] min_pwr: 0 max_pwr: 110
[ 0.349572@1] schedtune: CPU[2] min_pwr: 0 max_pwr: 1048
[ 0.349593@1] schedtune: CPU[3] min_pwr: 0 max_pwr: 1048
[ 0.349614@1] schedtune: CPU[4] min_pwr: 0 max_pwr: 1048
[ 0.349635@1] schedtune: CPU[5] min_pwr: 0 max_pwr: 1048
[ 0.349655@1] schedtune: SYSTEM min_pwr: 0 max_pwr: 4902
[ 0.349676@1] schedtune: using normalization constants mul: 2882587190 sh1: 1 sh2: 12
[ 0.349702@1] schedtune: verify normalization constants...
[ 0.349721@1] schedtune: max_pwr/2^0: 4902 => norm_pwr: 1024
[ 0.349740@1] schedtune: max_pwr/2^1: 2451 => norm_pwr: 512
[ 0.349759@1] schedtune: max_pwr/2^2: 1225 => norm_pwr: 255
[ 0.349778@1] schedtune: max_pwr/2^3: 612 => norm_pwr: 127
[ 0.349797@1] schedtune: max_pwr/2^4: 306 => norm_pwr: 63
[ 0.349816@1] schedtune: max_pwr/2^5: 153 => norm_pwr: 31
[ 0.349835@1] schedtune: configured to support 5 boost groups
[ 0.364311@2] cpuidle: using governor menu
[ 0.364431@2] register canvas platform driver
[ 0.364467@2] register rdma platform driver
[ 0.364501@2] aml_vdac_init: module init
[ 0.365837@2] vdso: 2 pages (1 code @ ffffff8009f07000, 1 data @ ffffff800aa45000)
[ 0.365866@2] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[ 0.367288@4] DMA: preallocated 2048 KiB pool for atomic allocations
[ 0.367459@4] clkmsr: clkmsr: driver init
[ 0.367474@4] codec_mm_module_init
[ 0.367507@4] media_configs_system_init
[ 0.367871@4] pstore: using zlib compression
[ 0.368576@4] console [pstore-1] enabled
[ 0.368643@4] pstore: Registered ramoops as persistent store backend
[ 0.368662@4] ramoops: attached 0x100000@0x7400000, ecc: 0/0
[ 0.368680@4] ramoops: ramoops_io_en:0 1 old:0x0 ftrace_size:0x40000
[ 0.370371@4] aml_iomap: amlogic iomap probe done
[ 0.370820@4] vpu: driver version: v20190314(8-g12b)
[ 0.370840@4] vpu: load vpu_clk: 666666667Hz(7)
[ 0.371035@4] vpu: clktree_init
[ 0.371090@4] vpu: vpu_probe OK
[ 0.374870@4] clkmsr: msr_clk_reg0=ffffff800836d004,msr_clk_reg2=ffffff800837c00c
[ 0.374901@4] clkmsr ffd18004.meson_clk_msr: failed to get msr ring reg0
[ 0.380149@4] aml_vdac_probe:probe start.cpu_id:6,name:meson-g12ab-vdac
[ 0.380325@4] aml_vdac_probe: ok
[ 0.380480@4] canvas_probe reg=00000000ff638000,size=2000
[ 0.380504@4] canvas maped reg_base =ffffff8008452000
[ 0.386015@4] rdma_probe,cpu_type:0, ver:0, len:8
[ 0.386233@4] rdma_register, rdma_table_addr ffffff8008475000 rdma_table_addr_phy a0600000 reg_buf ffffffc09b1c8000
[ 0.386261@4] rdma_register success, handle 1 table_size 32768
[ 0.386278@4] set_rdma_handle video rdma handle = 1.
[ 0.386294@4] g12b revb!!!!
[ 0.386349@4] rdma_register, rdma_table_addr ffffff8008491000 rdma_table_addr_phy a0608000 reg_buf ffffffc09b1e0000
[ 0.386375@4] rdma_register success, handle 2 table_size 32768
[ 0.386392@4] set_rdma_handle video rdma handle = 2.
[ 0.387432@4] aml_snd_reg_map[0], reg:ff640000, size:2000
[ 0.387462@4] aml_snd_reg_map[1], reg:ff642000, size:2000
[ 0.387489@4] aml_snd_reg_map[2], reg:ff64a000, size:2000
[ 0.387514@4] aml_snd_reg_map[3], reg:ff656000, size:1800
[ 0.387542@4] aml_snd_reg_map[4], reg:ffd01000, size:1000
[ 0.387558@4] amlogic auge_snd_iomap probe done
[ 0.390264@4] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[ 0.390352@4] codec_mm codec_mm: assigned reserved memory node linux,codec_mm_cma
[ 0.390376@4] codec_mm_probe ok
[ 0.549082@4] HugeTLB registered 2 MB page size, pre-allocated 0 pages
[ 0.549742@4] vgaarb: loaded
[ 0.549993@4] SCSI subsystem initialized
[ 0.550212@4] usbcore: registered new interface driver usbfs
[ 0.550275@4] usbcore: registered new interface driver hub
[ 0.550361@4] usbcore: registered new device driver usb
[ 0.550474@4] Linux video capture interface: v2.00
[ 0.550561@4] pps_core: LinuxPPS API ver. 1 registered
[ 0.550579@4] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[ 0.550618@4] PTP clock support registered
[ 0.550914@4] dmi: Firmware registration failed.
[ 0.551226@4] secmon: reserve_mem_size:0x300000
[ 0.551317@4] secmon secmon: assigned reserved memory node linux,secmon
[ 0.551730@4] secmon: get page:ffffffbf00140000, 5000
[ 0.551750@4] secmon: share in base: 0xffffffc0050fe000, share out base: 0xffffffc0050ff000
[ 0.551774@4] secmon: phy_in_base: 0x50fe000, phy_out_base: 0x50ff000
[ 0.552580@4] hdmitx: system: amhdmitx_probe start
[ 0.552598@4] hdmitx: system: Ver: 20190624
[ 0.552635@4] hdmitx: system: hdmitx_device.chip_type : 11
[ 0.552700@4] hdmitx: system: not find match pwr-ctl
[ 0.552746@4] hdmitx: system: not find drm_amhdmitx
[ 0.552782@4] hdmitx: system: hpd irq = 37
[ 0.552896@4] hdmitx: system: hdcp22_tx_skp failed to probe
[ 0.552914@4] hdmitx: system: hdcp22_tx_esm failed to probe
[ 0.553302@4] vout: vout1: register server: hdmitx_vout_server
[ 0.553322@4] vout: vout2: register server: hdmitx_vout2_server
[ 0.553811@4] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[ 0.553837@4] hdmitx: hdmitx20: Mapped PHY: 0xff634400
[ 0.553860@4] hdmitx: hdmitx20: Mapped PHY: 0xff900000
[ 0.553889@4] hdmitx: hdmitx20: Mapped PHY: 0xff800000
[ 0.553908@4] hdmitx: hdmitx20: Mapped PHY: 0xff63c000
[ 0.553925@4] hdmitx: hdmitx20: Mapped PHY: 0xffd00000
[ 0.553942@4] hdmitx: hdmitx20: Mapped PHY: 0xff608000
[ 0.553960@4] hdmitx: hdmitx20: Mapped PHY: 0xff600000
[ 0.553978@4] hdmitx: hdmitx20: Mapped PHY: 0xffe01000
[ 0.553999@4] hdmitx: hw: hdmitx_get_format:0x0
[ 0.554014@4] hdmitx: hw: P_HHI_HDMI_CLK_CNTL :0x100
[ 0.554030@4] hdmitx: hw: P_HHI_HDMI_PLL_CNTL :0x20000000
[ 0.554267@4] hdmitx: hw: avmute set to 1
[ 0.554284@4] hdmitx: system: fmt_attr default
[ 0.554358@4] hdmitx: system: amhdmitx_probe end
[ 0.554865@4] lcd: driver version: 20181012(5-g12a)
[ 0.554976@4] lcd: detect mode: tablet, fr_auto_policy: 0, key_valid: 0
[ 0.554996@4] lcd: detect lcd_clk_path: 1
[ 0.555224@4] lcd: lcd_clktree_probe
[ 0.555241@4] lcd: status: 3
[ 0.555258@4] vout: vout1: register server: lcd_vout_server
[ 0.555275@4] vout: vout2: register server: lcd_vout2_server
[ 0.555292@4] lcd: lcd_get_config from dts
[ 0.555310@4] lcd: error: failed to get null
[ 0.555327@4] lcd: , invalid, 0bit, 1024x600
[ 0.555345@4] lcd: error: Out of clock range, reset to default setting
[ 0.555427@4] lcd: error: lcd_debug_info_if is null
[ 0.555560@4] lcd: lcd_fops_create OK
[ 0.555606@4] lcd: request lcd_vsync_irq successful
[ 0.555644@4] lcd: request lcd_vsync2_irq successful
[ 0.555661@4] lcd: lcd_probe ok
[ 0.555932@4] vout: create vout attribute OK
[ 0.556040@4] vout: vout_fops_create OK
[ 0.556057@4] vout: vout1: register server: nulldisp_vout_server
[ 0.556146@4] vout: tvout monitor interval:500(ms), timeout cnt:20
[ 0.556177@4] hdmitx: hdmitx_set_current_vmode[3724]
[ 0.556194@4] hdmitx: system: recalc before 1080p60hz 60 1
[ 0.556212@4] hdmitx: system: recalc after 1080p60hz 2997 50
[ 0.556228@4] hdmitx: alread display in uboot
[ 0.556244@4] vout: init mode 1080p60hz set ok
[ 0.556259@4] vout: aml_tvout_mode_monitor
[ 0.556281@4] vout: aml_vout_probe OK
[ 0.556710@4] amlogic-pcie-v2 fc000000.pcieA: amlogic_pcie_probe!
[ 0.558955@4] OF: PCI: host bridge /pcieA@fc000000 ranges:
[ 0.558986@4] OF: PCI: IO 0xfc600000..0xfc6fffff -> 0x00000000
[ 0.559009@4] OF: PCI: MEM 0xfc700000..0xfdffffff -> 0xfc700000
[ 0.559795@4] amlogic-pcie-v2 fc000000.pcieA: Set the RC Bus Master, Memory Space and I/O Space enables.
[ 0.559824@4] amlogic-pcie-v2 fc000000.pcieA: normal gpio
[ 0.559860@4] amlogic-pcie-v2 fc000000.pcieA: GPIO normal: amlogic_pcie_assert_reset
[ 0.650404@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 0.826563@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.002724@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.178869@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.355021@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.531166@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.707323@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 1.883473@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 2.059618@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 2.235764@4] amlogic-pcie-v2 fc000000.pcieA: Error: Wait linkup timeout.
[ 2.330234@4] amlogic-pcie-v2 fc000000.pcieA: phy link never came up
[ 2.330379@4] amlogic-pcie-v2 fc000000.pcieA: PCI host bridge to bus 0000:00
[ 2.330403@4] pci_bus 0000:00: root bus resource [bus 00-ff]
[ 2.330422@4] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff]
[ 2.330441@4] pci_bus 0000:00: root bus resource [mem 0xfc700000-0xfdffffff]
[ 2.330483@4] amlogic-pcie-v2 fc000000.pcieA: link timeout, disable PCIE PLL
[ 2.330506@4] amlogic-pcie-v2 fc000000.pcieA: power down pcie phy
[ 2.330788@4] chip type:0x29
[ 2.331092@4] Advanced Linux Sound Architecture Driver Initialized.
[ 2.331557@4] Bluetooth: Core ver 2.22
[ 2.331612@4] NET: Registered protocol family 31
[ 2.331629@4] Bluetooth: HCI device and connection manager initialized
[ 2.331653@4] Bluetooth: HCI socket layer initialized
[ 2.331673@4] Bluetooth: L2CAP socket layer initialized
[ 2.331712@4] Bluetooth: SCO socket layer initialized
[ 2.332083@4] NetLabel: Initializing
[ 2.332101@4] NetLabel: domain hash size = 128
[ 2.332118@4] NetLabel: protocols = UNLABELED CIPSOv4
[ 2.332167@4] NetLabel: unlabeled traffic allowed by default
[ 2.333828@4] clocksource: Switched to clocksource arch_sys_counter
[ 2.385983@4] VFS: Disk quotas dquot_6.6.0
[ 2.386059@4] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 2.386196@4] FS-Cache: Loaded
[ 2.393719@4] jtag: module init
[ 2.394089@4] NET: Registered protocol family 2
[ 2.394514@4] TCP established hash table entries: 32768 (order: 6, 262144 bytes)
[ 2.394713@4] TCP bind hash table entries: 32768 (order: 7, 524288 bytes)
[ 2.394914@4] TCP: Hash tables configured (established 32768 bind 32768)
[ 2.394981@4] UDP hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.395031@4] UDP-Lite hash table entries: 2048 (order: 4, 65536 bytes)
[ 2.395192@4] NET: Registered protocol family 1
[ 2.396835@4] wifi: power_on_pin_OD = 0;
[ 2.396860@4] aml_wifi wifi: [wifi_dev_probe] no power_on_pin2
[ 2.396959@4] aml_wifi wifi: [pwm_double_channel_conf_dt] wifi pwm dt ok
[ 2.396986@4] aml_wifi wifi: [pwm_double_channel_conf] wifi pwm conf ok
[ 2.397006@4] aml_wifi wifi: [wifi_dev_probe] dhd_static_buf setup
[ 2.397023@4] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem 1.579.77.41.9
[ 2.397267@4] Wifi: bcmdhd_init_wlan_mem: bcmdhd_init_wlan_mem prealloc ok
[ 2.397287@4] aml_wifi wifi: [wifi_dev_probe] interrupt_pin=483
[ 2.397306@4] aml_wifi wifi: [wifi_dev_probe] irq_num=0, irq_trigger_type=1
[ 2.397325@4] aml_wifi wifi: [wifi_dev_probe] power_on_pin=482
[ 2.397342@4] aml_wifi wifi: [wifi_dev_probe] clock_32k_pin=0
[ 2.397521@4] aml_wifi wifi: [wifi_setup_dt] wifi_setup_dt
[ 2.397600@4] aml_wifi wifi: [wifi_setup_dt] irq num is:(103)
[ 2.397620@4] aml_wifi wifi: [wifi_setup_dt] interrupt_pin(483)
[ 2.397648@4] aml_wifi wifi: [wifi_setup_dt] power_on_pin(482)
[ 2.397910@4] Trying to unpack rootfs image as initramfs...
[ 2.699216@4] Freeing initrd memory: 8272K
[ 2.700633@4] hw perfevents: clusterb_enabled = 1
[ 2.700653@4] hw perfevents: cpumasks 0x3, 0x3c
[ 2.700695@4] hw perfevents: cluster A irq = 10
[ 2.700745@4] hw perfevents: cluster B irq = 11
[ 2.700826@4] hw perfevents: enabled with armv8_pmuv3 PMU driver, 7 counters available
[ 2.702965@4] audit: initializing netlink subsys (disabled)
[ 2.703031@4] audit: type=2000 audit(2.640:1): initialized
[ 2.703634@4] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[ 2.711587@4] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[ 2.711801@4] exFAT: Version 1.2.9
[ 2.712543@4] Registering sdcardfs 0.1
[ 2.713066@4] FS-Cache: Netfs 'cifs' registered for caching
[ 2.713327@4] Key type cifs.spnego registered
[ 2.713355@4] Key type cifs.idmap registered
[ 2.713375@4] ntfs: driver 2.1.32 [Flags: R/O].
[ 2.713599@4] jffs2: version 2.2. (NAND) (SUMMARY) © 2001-2006 Red Hat, Inc.
[ 2.714081@4] fuse init (API version 7.26)
[ 2.717696@4] NET: Registered protocol family 38
[ 2.717721@4] Key type asymmetric registered
[ 2.717738@4] Asymmetric key parser 'x509' registered
[ 2.717930@4] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 243)
[ 2.718093@4] io scheduler noop registered (default)
[ 2.718112@4] io scheduler deadline registered
[ 2.718151@4] io scheduler cfq registered
[ 2.725960@5] random: fast init done
[ 2.726015@5] random: crng init done
[ 2.726459@4] gpiomem-aml ff634000.gpiomem: Initialised: Registers at 0xff634000
[ 2.726624@4] gpiomem-aml ff800000.gpiomem_ao: Initialised: Registers at 0xff800000
[ 2.726762@4] [drm] Initialized
[ 2.726911@4] Unable to detect cache hierarchy for CPU 0
[ 2.734331@4] brd: module loaded
[ 2.738707@4] loop: module loaded
[ 2.739751@4] mtdoops: mtd device (mtddev=name/number) must be supplied
[ 2.740856@4] libphy: Fixed MDIO Bus: probed
[ 2.741075@4] tun: Universal TUN/TAP device driver, 1.6
[ 2.741095@4] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 2.741771@4] REG0:Addr = ffffff800863c540
[ 2.741796@4] ee eth reset:Addr = ffffff800863e008
[ 2.741847@4] auto_cali_idx 0
[ 2.742232@4] meson6-dwmac ff3f0000.ethernet: no reset control found
[ 2.742254@4] stmmac - user ID: 0x11, Synopsys ID: 0x37
[ 2.742271@4] Ring mode enabled
[ 2.742286@4] DMA HW capability register supported
[ 2.742298@4] Normal descriptors
[ 2.742319@4] RX Checksum Offload Engine supported
[ 2.742334@4] COE Type 2
[ 2.742348@4] TX Checksum insertion supported
[ 2.742363@4] Wake-Up On Lan supported
[ 2.742408@4] Enable RX Mitigation via HW Watchdog Timer
[ 2.749631@4] libphy: stmmac: probed
[ 2.749660@4] eth%d: PHY ID 001cc916 at 0 IRQ POLL (stmmac-0:00) active
[ 2.749679@4] eth%d: PHY ID 001cc916 at 1 IRQ POLL (stmmac-0:01)
[ 2.750848@4] PPP generic driver version 2.4.2
[ 2.751026@4] PPP BSD Compression module registered
[ 2.751046@4] PPP Deflate Compression module registered
[ 2.751075@4] PPP MPPE Compression module registered
[ 2.751093@4] NET: Registered protocol family 24
[ 2.751174@4] usbcore: registered new interface driver asix
[ 2.751255@4] usbcore: registered new interface driver ax88179_178a
[ 2.751313@4] usbcore: registered new interface driver cdc_ether
[ 2.751367@4] usbcore: registered new interface driver cdc_eem
[ 2.751423@4] usbcore: registered new interface driver net1080
[ 2.751479@4] usbcore: registered new interface driver rndis_host
[ 2.751534@4] usbcore: registered new interface driver cdc_subset
[ 2.751588@4] usbcore: registered new interface driver zaurus
[ 2.751650@4] usbcore: registered new interface driver cdc_ncm
[ 2.751705@4] usbcore: registered new interface driver qmi_wwan
[ 2.751742@4] GobiNet: Quectel_Linux&Android_GobiNet_Driver_V1.6.1
[ 2.751798@4] usbcore: registered new interface driver GobiNet
[ 2.752280@4] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 2.752300@4] ehci-pci: EHCI PCI platform driver
[ 2.752357@4] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 2.752390@4] ohci-pci: OHCI PCI platform driver
[ 2.752841@4] usbcore: registered new interface driver cdc_acm
[ 2.752859@4] cdc_acm: USB Abstract Control Model driver for USB modems and ISDN adapters
[ 2.752922@4] usbcore: registered new interface driver cdc_wdm
[ 2.752985@4] usbcore: registered new interface driver usb-storage
[ 2.753074@4] usbcore: registered new interface driver usbserial
[ 2.753126@4] usbcore: registered new interface driver usbserial_generic
[ 2.753166@4] usbserial: USB Serial support registered for generic
[ 2.753219@4] usbcore: registered new interface driver ch341
[ 2.753257@4] usbserial: USB Serial support registered for ch341-uart
[ 2.753310@4] usbcore: registered new interface driver cp210x
[ 2.753353@4] usbserial: USB Serial support registered for cp210x
[ 2.753406@4] usbcore: registered new interface driver ftdi_sio
[ 2.753446@4] usbserial: USB Serial support registered for FTDI USB Serial Device
[ 2.753504@4] usbcore: registered new interface driver option
[ 2.753548@4] usbserial: USB Serial support registered for GSM modem (1-port)
[ 2.753599@4] usbcore: registered new interface driver pl2303
[ 2.753637@4] usbserial: USB Serial support registered for pl2303
[ 2.754011@4] mousedev: PS/2 mouse device common for all mice
[ 2.754227@4] usbcore: registered new interface driver xpad
[ 2.754407@4] i2c /dev entries driver
[ 2.754610@4] IR NEC protocol handler initialized
[ 2.754628@4] IR RC5(x/sz) protocol handler initialized
[ 2.754645@4] IR RC6 protocol handler initialized
[ 2.754661@4] IR JVC protocol handler initialized
[ 2.754676@4] IR Sony protocol handler initialized
[ 2.754692@4] IR SANYO protocol handler initialized
[ 2.754708@4] IR Sharp protocol handler initialized
[ 2.754724@4] IR MCE Keyboard/mouse protocol handler initialized
[ 2.754740@4] IR XMP protocol handler initialized
[ 2.754813@4] usbcore: registered new interface driver uvcvideo
[ 2.754830@4] USB Video Class driver (1.1.1)
[ 2.754887@4] usbcore: registered new interface driver cx231xx
[ 2.754905@4] Driver for 1-wire Dallas network protocol.
[ 2.755229@4] md: linear personality registered for level -1
[ 2.755547@4] device-mapper: ioctl: 4.35.0-ioctl (2016-06-23) initialised: dm-devel@redhat.com
[ 2.755703@4] device-mapper: verity-avb: AVB error handler initialized with vbmeta device:
[ 2.755753@4] Bluetooth: HCI UART driver ver 2.3
[ 2.755771@4] Bluetooth: HCI UART protocol H4 registered
[ 2.757165@2] ledtrig-cpu: registered to indicate activity on CPUs
[ 2.757595@2] hidraw: raw HID events driver (C) Jiri Kosina
[ 2.757896@2] usbcore: registered new interface driver usbhid
[ 2.757916@2] usbhid: USB HID core driver
[ 2.758377@2] meson_cpufreq_init: ignor dsu clk!
[ 2.758397@2] meson_cpufreq_init: ignor dsu pre parent clk!
[ 2.758453@2] value of voltage_tolerance 0
[ 2.758470@2] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[ 2.758487@2] value of gp1_clk_target 0
[ 2.759487@2] cpu cpu0: meson_cpufreq_init: CPU 0 initialized
[ 2.760199@2] meson_cpufreq_init: ignor dsu clk!
[ 2.760219@2] meson_cpufreq_init: ignor dsu pre parent clk!
[ 2.760298@2] value of voltage_tolerance 0
[ 2.760316@2] meson_cpufreq_init:don't find the node <dynamic_gp1_clk>
[ 2.760332@2] value of gp1_clk_target 0
[ 2.761485@2] cpu cpu2: meson_cpufreq_init: CPU 2 initialized
[ 2.762251@2] ff803000.serial: clock gate not found
[ 2.762281@2] meson_uart ff803000.serial: ==uart0 reg addr = ffffff80086fc000
[ 2.762312@2] ff803000.serial: ttyS0 at MMIO 0xff803000 (irq = 25, base_baud = 1500000) is a meson_uart
[ 2.762331@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 0 to 115200
[ 5.495311@2] console [ttyS0] enabled
[ 5.499206@2] meson_uart ffd24000.serial: ==uart1 reg addr = ffffff80086fe000
[ 5.506074@2] ffd24000.serial: ttyS1 at MMIO 0xffd24000 (irq = 34, base_baud = 1500000) is a meson_uart
[ 5.515569@2] meson_uart ffd22000.serial: ==uart3 reg addr = ffffff800882e000
[ 5.522538@2] ffd22000.serial: ttyS3 at MMIO 0xffd22000 (irq = 35, base_baud = 1500000) is a meson_uart
[ 5.532513@2] amlogic-new-usb2-v2 ffe09000.usb2phy: USB2 phy probe:phy_mem:0xffe09000, iomap phy_base:0xffffff8008830000
[ 5.542813@2] amlogic-new-usb3-v2 ffe09080.usb3phy: This phy has no usb port
[ 5.549753@2] amlogic-new-usb3-v2 ffe09080.usb3phy: pci-e driver probe, disable USB 3.0 function!!!
[ 5.558783@2] amlogic-new-usb3-v2 ffe09080.usb3phy: USB3 phy probe:phy_mem:0xffe09080, iomap phy_base:0xffffff800883b080
[ 5.569988@2] edt_ft5x06 3-0038: probing for EDT FT5x06 I2C
[ 5.575424@2] 4-0020 supply vcc not found, using dummy regulator
[ 5.581593@2] pca953x 4-0020: interrupt support not compiled in
[ 5.587518@2] rtc-hym8563 4-0051: no valid clock/calendar values available
[ 5.593912@2] rtc-hym8563 4-0051: rtc core: registered hym8563 as rtc0
[ 5.600653@2] mcu_probe
[ 5.602779@2] mcu_probe: board: 3, hwver: 2
[ 5.607327@2] create_mcu_attrs
[ 5.610006@2] mcu_probe,wol enable=0
[ 5.614871@2] gpio-keypad gpio_keypad: power key(116) registed.
[ 5.619477@2] input: gpio_keypad as /devices/platform/gpio_keypad/input/input0
[ 5.626697@2] meson-remote: Driver init
[ 5.630499@2] meson-remote: remote_probe
[ 5.634324@2] meson-remote ff808040.rc: protocol = 0x1
[ 5.639433@2] meson-remote ff808040.rc: don't find the node <led_blink>
[ 5.646023@2] meson-remote ff808040.rc: led_blink = 0
[ 5.651048@2] meson-remote ff808040.rc: don't find the node <led_blink_frq>
[ 5.657982@2] meson-remote ff808040.rc: led_blink_frq = 100
[ 5.663622@2] meson-remote ff808040.rc: platform_data irq =33
[ 5.669351@2] meson-remote ff808040.rc: custom_number = 1
[ 5.674715@2] meson-remote ff808040.rc: ptable->map_size = 13
[ 5.680428@2] meson-remote ff808040.rc: ptable->custom_name = khadas-ir
[ 5.687013@2] meson-remote ff808040.rc: ptable->custom_code = 0xff00
[ 5.693341@2] meson-remote ff808040.rc: ptable->release_delay = 80
[ 5.699495@2] meson-remote ff808040.rc: default protocol = 0x1 and id = 0
[ 5.706254@2] meson-remote ff808040.rc: reg=0x0, val=0x1f40190
[ 5.712059@2] meson-remote ff808040.rc: reg=0x4, val=0x12c00c8
[ 5.717868@2] meson-remote ff808040.rc: reg=0x8, val=0x960050
[ 5.723586@2] meson-remote ff808040.rc: reg=0xc, val=0x480028
[ 5.729305@2] meson-remote ff808040.rc: reg=0x10, val=0x70fa0013
[ 5.735285@2] meson-remote ff808040.rc: reg=0x18, val=0x8616800
[ 5.741178@2] meson-remote ff808040.rc: reg=0x1c, val=0x9f00
[ 5.746812@2] meson-remote ff808040.rc: reg=0x20, val=0x0
[ 5.752185@2] meson-remote ff808040.rc: reg=0x24, val=0x0
[ 5.757558@2] meson-remote ff808040.rc: reg=0x28, val=0x0
[ 5.763131@2] input: aml_keypad as /devices/platform/ff808040.rc/input/input1
[ 5.770227@2] meson-remote: IR XMP protocol handler initialized
[ 5.776084@2] efuse efuse: open efuse clk gate error!!
[ 5.781164@2] efusekeynum: 1
[ 5.784005@2] efusekeyname: mac offset: 0 size: 6
[ 5.790478@2] efuse efuse: probe OK!
[ 5.794911@3] ion_dev soc:ion_dev: assigned reserved memory node linux,ion-dev
[ 5.801414@3] ge2d: ge2d_init_module
[ 5.804812@3] ge2d: ge2d_dev major:510
[ 5.808543@3] ge2d: clock source clk_ge2d_gate ffffffc09af4e280
[ 5.814346@3] ge2d: clock clk_ge2d source ffffffc09af4eec0
[ 5.819810@3] ge2d: clock source clk_vapb_0 ffffffc09af4e040
[ 5.825423@3] ge2d: ge2d init clock is 500000000 HZ, VPU clock is 666666656 HZ
[ 5.832664@3] ge2d: ge2d clock is 499 MHZ
[ 5.836607@3] ge2d: find address resource
[ 5.840594@3] ge2d: map io source 0x00000000ff940000,size=65536 to 0xffffff80088d0000
[ 5.848387@3] ge2d: reserved mem init failed
[ 5.852632@3] ge2d: ge2d: pdev=ffffffc09b17ec00, irq=43, clk=ffffffc09af4e280
[ 5.859761@3] ge2d: ge2d start monitor
[ 5.863497@4] ge2d: ge2d workqueue monitor start
[ 5.863670@3] [tsync_pcr_init]init success.
[ 5.863759@3] amvideom vsync irq: 44
[ 5.864042@3] create_ge2d_work_queue video task ok
[ 5.864063@3] fb: osd_init_module
[ 5.864219@3] fb: viu vsync irq: 44
[ 5.864226@3] fb: viu2 vsync irq: 53
[ 5.864272@3] 0x000000db:Y=db,U=0,V=0
[ 5.864274@3] 0x000000dc:Y=dc,U=0,V=0
[ 5.864275@3] 0x000000dd:Y=dd,U=0,V=0
[ 5.864276@3] 0x000000de:Y=de,U=0,V=0
[ 5.864277@3] 0x000000df:Y=df,U=0,V=0
[ 5.864277@3] 0x000000e0:Y=e0,U=0,V=0
[ 5.868126@3] fb: osd_rdma_init: rdma_table p=0xa0610000,op=0xa0610000 , v=0xffffff800888d000
[ 5.868140@3] rdma_register, rdma_table_addr ffffff80088c2000 rdma_table_addr_phy a0611000 reg_buf ffffffc09b308000
[ 5.868142@3] rdma_register success, handle 3 table_size 4096
[ 5.868143@3] fb: osd_rdma_init:osd rdma handle = 3.
[ 5.868150@3] fb: mem_size: 0x800000
[ 5.868151@3] fb: mem_size: 0x4b80000
[ 5.868152@3] fb: mem_size: 0x100000
[ 5.868153@3] fb: mem_size: 0x100000
[ 5.868153@3] fb: mem_size: 0x800000
[ 5.868181@3] meson-fb meson-fb: assigned reserved memory node linux,meson-fb
[ 5.868182@3] fb: reserved memory base:0x000000007f800000, size:800000
[ 5.868264@3] fb: fb def : 1920 1080 1920 2160 32
[ 5.868265@3] fb: init fbdev bpp is:32
[ 5.982122@5] fb: malloc_osd_memory, cma:ffffff800accd0d8
[ 5.982124@5] fb: malloc_osd_memory, 1232, base:0x000000007f800000, size:8388608
[ 5.982144@5] fb: use ion buffer for fb memory, fb_index=0
[ 5.982146@5] fb: OSD0 as afbcd mode,afbc_type=2
[ 6.003171@5] meson-fb meson-fb: create ion_client ffffffc09ac8bc00, handle=ffffffc07f024840
[ 6.003175@5] meson-fb meson-fb: ion memory(0): created fb at 0x00000000e5800000, size 75 MiB
[ 6.003177@5] fb: 0, phy: 0x00000000e5800000, vir:0xffffff800b101000, size=77312K
[ 6.003177@5]
[ 6.003180@5] fb: Frame buffer memory assigned at
[ 6.003180@5] fb: 0, phy: 0x00000000e5800000, vir:0xffffff800b101000, size=77312K
[ 6.003180@5]
[ 6.003182@5] fb: 0, phy: 0x00000000e5800000, vir:0xffffff800b101000, size=77312K
[ 6.003182@5]
[ 6.003184@5] fb: logo_index=0,fb_index=0
[ 6.003185@5] fb: ---------------clear fb0 memory ffffff800b101000
[ 6.015412@5] fb: osd[0] canvas.idx =0x40
[ 6.015413@5] fb: osd[0] canvas.addr=0xe5800000
[ 6.015414@5] fb: osd[0] canvas.width=7680
[ 6.015415@5] fb: osd[0] canvas.height=2160
[ 6.015416@5] fb: osd[0] frame.width=1920
[ 6.015416@5] fb: osd[0] frame.height=1080
[ 6.015417@5] fb: osd[0] out_addr_id =0x1
[ 8.064598@5] Console: switching to colour frame buffer device 240x67
[ 9.209838@5] fb: osd[0] enable: 1 (swapper/0)
[ 10.234202@5] fb: set osd0 reverse as NONE
[ 11.257843@0] fb: osd probe OK
[ 11.258202@0] hdmitx: hdcp: hdmitx_hdcp_init
[ 11.259987@2] vout: vout2: create vout2 attribute OK
[ 11.264680@0] vout: vout2: vout2_fops_create OK
[ 11.269177@0] vout: vout2: clktree_init
[ 11.272923@0] vout: vout2: register server: nulldisp_vout2_server
[ 11.279125@0] vout: vout2: init mode null set ok
[ 11.283516@2] vout: vout2: aml_vout2_probe OK
[ 11.287876@2] DI: di_module_init ok.
[ 11.291370@2] DI: di_module_init: major 507
[ 11.295807@2] deinterlace deinterlace: assigned reserved memory node linux,di_cma
[ 11.302991@2] DI: CMA size 0x2800000.
[ 11.306630@2] pre_irq:68
[ 11.309131@2] post_irq:69
[ 11.311733@2] DI: di_probe allocate rdma channel 0.
[ 11.316593@2] di_get_vpu_clkb: get clk vpu error.
[ 11.321266@2] DI: vpu clkb <334000000, 667000000>
[ 11.321825@4] vout: aml_tvout_mode_work: monitor_timeout
[ 11.331260@2] DI:enable vpu clkb.
[ 11.334533@2] 0x000000e1:Y=e1,U=0,V=0
[ 11.338167@2] 0x000000e2:Y=e2,U=0,V=0
[ 11.341800@2] 0x000000e3:Y=e3,U=0,V=0
[ 11.345445@2] 0x000000f0:Y=f0,U=0,V=0
[ 11.349086@2] 0x000000f1:Y=f1,U=0,V=0
[ 11.352726@2] 0x000000f2:Y=f2,U=0,V=0
[ 11.356365@2] 0x000000f3:Y=f3,U=0,V=0
[ 11.360004@2] 0x000000f4:Y=f4,U=0,V=0
[ 11.363644@2] 0x000000f5:Y=f5,U=0,V=0
[ 11.367283@2] 0x000000f6:Y=f6,U=0,V=0
[ 11.370927@2] 0x000000f7:Y=f7,U=0,V=0
[ 11.374564@2] 0x000000f8:Y=f8,U=0,V=0
[ 11.378204@2] 0x000000f9:Y=f9,U=0,V=0
[ 11.381843@2] 0x000000fa:Y=fa,U=0,V=0
[ 11.385479@2] 0x000000fb:Y=fb,U=0,V=0
[ 11.389124@2] 0x000000fc:Y=fc,U=0,V=0
[ 11.392766@2] 0x000000fd:Y=fd,U=0,V=0
[ 11.396404@2] 0x000000fe:Y=fe,U=0,V=0
[ 11.400044@2] 0x000000ff:Y=ff,U=0,V=0
[ 11.403684@2] 0x0000003a:Y=3a,U=0,V=0
[ 11.407323@2] 0x0000003b:Y=3b,U=0,V=0
[ 11.410963@2] 0x0000003c:Y=3c,U=0,V=0
[ 11.414604@2] 0x0000003d:Y=3d,U=0,V=0
[ 11.418244@2] DI: support post write back 61.
[ 11.422671@2] DI: di_probe:Di use HRTIMER
[ 11.426637@2] di_probe:ok
[ 11.429207@2] vdin_drv_init: major 506
[ 11.433062@2] rdma_register, rdma_table_addr ffffff80088ca000 rdma_table_addr_phy a0612000 reg_buf ffffffc07ec77a00
[ 11.443300@2] rdma_register success, handle 4 table_size 512
[ 11.448927@2] vdin_drv_probe:vdin.0 rdma hanld 4.
[ 11.453722@2] vdin vdin0: assigned reserved memory node linux,vdin0_cma
[ 11.460193@2]
[ 11.460193@2] vdin memory resource done.
[ 11.465834@2] vdin0 cma_mem_size = 64 MB
[ 11.469721@2] vdin0 irq: 41 rdma irq: 2
[ 11.473544@2] set_canvas_manual = 0
[ 11.477009@2] no urgent_en found
[ 11.480221@2] get fclk_div5 err
[ 11.483339@2] vdin_drv_probe: vdin cannot get msr clk !!!
[ 11.488719@2] vdin_drv_probe: driver initialized ok
[ 11.493608@2] rdma_register, rdma_table_addr ffffff80088cc000 rdma_table_addr_phy a0613000 reg_buf ffffffc07ec77c00
[ 11.503964@2] rdma_register success, handle 5 table_size 512
[ 11.509595@2] vdin_drv_probe:vdin.1 rdma hanld 5.
[ 11.514357@2] vdin vdin1: assigned reserved memory node linux,vdin1_cma
[ 11.520860@2]
[ 11.520860@2] vdin memory resource done.
[ 11.526499@2] vdin1 cma_mem_size = 64 MB
[ 11.530393@2] vdin1 irq: 42 rdma irq: 4
[ 11.534210@2] set_canvas_manual = 0
[ 11.537666@2] no urgent_en found
[ 11.540887@2] get fclk_div5 err
[ 11.544005@2] vdin_drv_probe: vdin cannot get msr clk !!!
[ 11.549375@2] vdin_debugfs_init only support debug vdin0 1
[ 11.554837@2] vdin_drv_probe: driver initialized ok
[ 11.559754@2] vdin_drv_init: vdin driver init done
[ 11.564456@2] [viuin..]viuin_init_module viuin module init
[ 11.570065@2] [viuin..]viuin_probe probe ok.
[ 11.574421@2] [RX]-hdmirx: hdmirx_init.
[ 11.577975@2] ESM HLD: Initializing...
[ 11.581751@2] tvin_afe: tvafe_drv_init: major 504
[ 11.586537@2] tvin_afe: tvafe_drv_init.
[ 11.590286@2] tvafe_vbi: vbi: vbi_init.
[ 11.594115@2] amvdec_csi module: init.
[ 11.597727@2] amvdec_csi_init_module:major 502
[ 11.602246@2] amvdec_csi module: init. ok
[ 11.606142@2] amlvid:info: amlvideo_init called[ 11.610473@2] amlvid:info: amlvideo_create_instance called
[ 11.615934@2] amlvid:info: v4l2_dev.name=:amlvideo-000
[ 11.621114@2] amlvideo-000: V4L2 device registered as video10
[ 11.626850@2] amlvideo2 probe called
[ 11.630320@2] amlvideo2_create_node[ 11.633683@2] amlvideo2: V4L2 device registered as video11
[ 11.639086@2] amlvideo2 probe called
[ 11.642629@2] amlvideo2_create_node[ 11.645997@2] amlvideo2: V4L2 device registered as video12
[ 11.651407@2] PPMGRDRV: warn: ppmgr module init func called
[ 11.657007@2] PPMGRDRV: info: ppmgr_driver_probe called
[ 11.662163@2] Reserved memory: failed to init DMA memory pool at 0x00000000e3000000, size 0 MiB
[ 11.670799@2] PPMGRDRV: info: ppmgr_dev major:501
[ 11.675793@2] ionvideo-000: V4L2 device registered as video13
[ 11.681196@2] ionvid: info: Video Technology Magazine Ion Video
[ 11.687089@2] ionvid: info: Capture Board ver 1.0 successfully loaded
[ 11.693608@2] picdec: picdec_driver_probe called.
[ 11.698283@2] picdec: probe of picdec failed with error -22
[ 11.703823@2] videosync_create_instance dev_s ffffffc09b320000,dev_s->dev ffffffc07ecda480
[ 11.711961@2] videosync_create_instance reg videosync.0
[ 11.717196@2] aml_vecm_init:module init
[ 11.717198@3] videosync_thread started
[ 11.724804@2]
[ 11.724804@2] VECM probe start
[ 11.729586@2] vlock_status_init vlock_en:0
[ 11.733559@2] Can't find wb_sel.
[ 11.736832@2] hdr:Can't find cfg_en_osd_100.
[ 11.741164@2] Can't find tx_op_color_primary.
[ 11.745589@2] amlogic, vecm[ 11.748185@2] vlock dt support: 1
[ 11.751477@2] vlock dt new_fsm: 0
[ 11.754774@2] vlock dt hwver: 0
[ 11.757891@2] vlock dt phlock_en: 0
[ 11.761354@2] Can't find vlock_en.
[ 11.764828@2] Can't find vlock_mode.
[ 11.768465@2] Can't find vlock_pll_m_limit.
[ 11.772716@2] Can't find vlock_line_limit.
[ 11.776874@2] param_config vlock_en:0
[ 11.780522@2] request amvecm_vsync2_irq successful
[ 11.785281@2] aml_vecm_probe: ok
[ 11.788509@2] amdolby_vision_init:module init
[ 11.792962@2]
[ 11.792962@2] amdolby_vision probe start & ver: 20181220
[ 11.799842@2]
[ 11.799842@2] cpu_id=2 tvmode=0
[ 11.804766@2] dolby_vision_init_receiver(dvel)
[ 11.809114@2] dolby_vision_init_receiver: dvel
[ 11.813619@2] amdolby_vision_probe: ok
[ 11.817285@2] prime_sl module init
[ 11.820816@2] reg base = ffffff80088f6000
[ 11.824669@2] gdc ff950000.gdc: assigned reserved memory node linux,gdc_cma
[ 11.831854@2] vm_init .
[ 11.834512@2] meson-mmc: mmc driver version: 3.02, 2017-05-15: New Emmc Host Controller
[ 11.842436@2] meson-mmc: >>>>>>>>hostbase ffffff80088fe000, dmode
[ 11.848287@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 11.853837@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 11.897828@2] meson-mmc: meson_mmc_probe() : success!
[ 11.906175@3] meson-mmc: >>>>>>>>hostbase ffffff8008a89000, dmode
[ 11.908853@3] meson-mmc: gpio_cd = 1ca
[ 11.949867@0] meson-mmc: meson_mmc_probe() : success!
[ 11.955188@1] meson-mmc: >>>>>>>>hostbase ffffff8008b13000, dmode
[ 11.955332@2] meson-aml-mmc ffe07000.emmc: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 11.955334@2] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 11.955336@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 11.955338@2] meson-mmc: Data 1 aligned delay is 0
[ 11.955340@2] meson-mmc: emmc: clk 199999997 tuning start
[ 11.955364@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 11.956183@2] meson-mmc: emmc: rx_tuning_result[1] = 40
[ 11.956993@2] meson-mmc: emmc: rx_tuning_result[2] = 40
[ 11.957841@2] meson-mmc: emmc: rx_tuning_result[3] = 40
[ 11.958661@2] meson-mmc: emmc: rx_tuning_result[4] = 40
[ 11.958663@2] meson-mmc: [prev_map] fixed_adj_win_map:30
[ 11.958664@2] meson-mmc: [0]=0
[ 11.958665@2] meson-mmc: [1]=1
[ 11.958665@2] meson-mmc: [2]=1
[ 11.958666@2] meson-mmc: [3]=1
[ 11.958667@2] meson-mmc: [4]=1
[ 11.958668@2] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 11.958670@2] meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104
[ 11.958692@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 11.959507@2] meson-mmc: emmc: rx_tuning_result[1] = 40
[ 11.960319@2] meson-mmc: emmc: rx_tuning_result[2] = 40
[ 11.961130@2] meson-mmc: emmc: rx_tuning_result[3] = 40
[ 11.961945@2] meson-mmc: emmc: rx_tuning_result[4] = 40
[ 11.961947@2] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 11.961948@2] meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208
[ 11.961970@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 11.961991@2] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 11.962780@2] meson-mmc: emmc: rx_tuning_result[2] = 40
[ 11.963569@2] meson-mmc: emmc: rx_tuning_result[3] = 40
[ 11.964355@2] meson-mmc: emmc: rx_tuning_result[4] = 40
[ 11.964357@2] meson-mmc: [>>>>>>>>bitmap_xor_dst] fixed_adj_win_map:2
[ 11.964357@2] meson-mmc: [0]=0
[ 11.964358@2] meson-mmc: [1]=1
[ 11.964359@2] meson-mmc: [2]=0
[ 11.964360@2] meson-mmc: [3]=0
[ 11.964361@2] meson-mmc: [4]=0
[ 11.964362@2] meson-mmc: [_find_fixed_adj_valid_win] fir_adj:1
[ 11.964363@2] meson-mmc: [>>>>>>>>prev_map_range] fixed_adj_win_map:495
[ 11.964364@2] meson-mmc: [1]=1
[ 11.964364@2] meson-mmc: [2]=1
[ 11.964365@2] meson-mmc: [3]=1
[ 11.964366@2] meson-mmc: [4]=1
[ 11.964366@2] meson-mmc: [0]=0
[ 11.964368@2] meson-mmc: left:3, right:0, mid:4, size:4
[ 11.964369@2] meson-mmc: step:0, delay1:0x0, delay2:0x0
[ 11.964372@2] meson-mmc: emmc: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000
[ 11.964373@2] meson-mmc: delay1:0x0, delay2:0x0
[ 11.964449@2] emmc: new HS200 MMC card at address 0001
[ 11.964793@2] emmc: clock 199999997, 8-bit-bus-width
[ 11.964793@2]
[ 11.964793@2] mmcblk0: emmc:0001 BJTD4R 29.1 GiB
[ 11.964954@2] mmcblk0boot0: emmc:0001 BJTD4R partition 1 4.00 MiB
[ 11.965104@2] mmcblk0boot1: emmc:0001 BJTD4R partition 2 4.00 MiB
[ 11.965256@2] mmcblk0rpmb: emmc:0001 BJTD4R partition 3 4.00 MiB
[ 11.965883@2] meson-mmc: Enter aml_emmc_partition_ops
[ 11.966229@2] meson-mmc: [mmc_read_partition_tbl] mmc read partition OK!
[ 11.966230@2] meson-mmc: add_emmc_partition
[ 11.966306@2] meson-mmc: [mmcblk0p01] bootloader offset 0x000000000000, size 0x000000400000
[ 11.966376@2] meson-mmc: [mmcblk0p02] reserved offset 0x000002400000, size 0x000004000000
[ 11.966442@2] meson-mmc: [mmcblk0p03] env offset 0x000006c00000, size 0x000000800000
[ 11.966510@2] meson-mmc: [mmcblk0p04] logo offset 0x000007c00000, size 0x000000800000
[ 11.966575@2] meson-mmc: [mmcblk0p05] ramdisk offset 0x000008c00000, size 0x000002000000
[ 11.966639@2] meson-mmc: [mmcblk0p06] rootfs offset 0x00000b400000, size 0x00073c800000
[ 11.966647@2] card key: card_blk_probe.
[ 11.966649@2] emmc_key_init:183 emmc key lba_start:0x12020,lba_end:0x12220
[ 11.966651@2] emmc key: emmc_key_init:205 ok.
[ 11.968419@2] meson-mmc: amlmmc_dtb_init: register dtb chardev
[ 11.968419@2] meson-mmc: calc 86c14a96, store 86c14a96
[ 11.970143@2] meson-mmc: calc 86c14a96, store 86c14a96
[ 11.970144@2] meson-mmc: total valid 2
[ 11.970250@2] meson-mmc: amlmmc_dtb_init: register dtb chardev OK
[ 11.970251@2] meson-mmc: Exit aml_emmc_partition_ops OK.
[ 12.350599@2] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 12.356109@2] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 12.401830@2] meson-mmc: meson_mmc_probe() : success!
[ 12.403313@2] aml_vrtc rtc: rtc core: registered aml_vrtc as rtc1
[ 12.408811@2] cectx ff80023c.aocec: cec driver date:2019/6/13:early suspend not report pw status
[ 12.408811@2]
[ 12.418907@2] cectx ff80023c.aocec: compatible:amlogic, aocec-g12a
[ 12.424922@2] cectx ff80023c.aocec: cecb_ver:0x1
[ 12.429510@2] cectx ff80023c.aocec: line_reg:0x1
[ 12.434111@2] cectx ff80023c.aocec: line_bit:0x3
[ 12.438696@2] cectx ff80023c.aocec: ee_to_ao:0x1
[ 12.443354@2] input: cec_input as /devices/virtual/input/input2
[ 12.449255@2] cectx ff80023c.aocec: not find 'port_num'
[ 12.454385@2] cectx ff80023c.aocec: using cec:1
[ 12.458901@2] cectx ff80023c.aocec: no hdmirx regs
[ 12.463664@2] cectx ff80023c.aocec: no hhi regs
[ 12.468167@2] cectx ff80023c.aocec: not find 'output'
[ 12.473194@2] cec: wake up flag:0
[ 12.477926@2] cectx ff80023c.aocec: irq cnt:2
[ 12.480934@2] cectx ff80023c.aocec: wakeup_reason:0x0
[ 12.485898@2] cectx ff80023c.aocec: cev val1: 0x0;val2: 0x0
[ 12.491398@2] cectx ff80023c.aocec: aml_cec_probe success end
[ 12.497249@2] unifykey: storage in base: 0xffffffc005000000
[ 12.502656@2] unifykey: storage out base: 0xffffffc005040000
[ 12.508290@2] unifykey: storage block base: 0xffffffc005080000
[ 12.514097@2] unifykey: probe done!
[ 12.517750@2] unifykey: no efuse-version set, use default value: -1
[ 12.523810@2] unifykey: key unify config unifykey-num is 16
[ 12.529389@2] unifykey: key unify fact unifykey-num is 16
[ 12.534729@2] unifykey: unifykey_devno: 1ed00000
[ 12.539401@2] unifykey: device unifykeys created ok
[ 12.544197@2] unifykey: aml_unifykeys_init done!
[ 12.548796@2] meson ts init
[ 12.551569@2] tsensor id: 0
[ 12.554381@2] tsensor trim info: 0xfa0080e1!
[ 12.558554@2] tsensor hireboot: 0xc0ff2b00
[ 12.562663@2] meson ts init
[ 12.565410@2] tsensor id: 1
[ 12.568219@2] tsensor trim info: 0xfa008136!
[ 12.572421@2] tsensor hireboot: 0xc0ff2b20
[ 12.576590@2] audio_dsp: [dsp]register dsp to char divece(257)
[ 12.582385@2] amaudio: amaudio: driver amaudio init!
[ 12.587418@2] amaudio: amaudio_init - amaudio: driver amaudio succuess!
[ 12.594117@2] sysled: module init
[ 12.597255@2] meson_wdt ffd0f0d0.watchdog: start watchdog
[ 12.602501@2] meson_wdt ffd0f0d0.watchdog: creat work queue for watch dog
[ 12.609371@2] meson_wdt ffd0f0d0.watchdog: AML Watchdog Timer probed done
[ 12.616303@2] amlogic rfkill init
[ 12.619384@2] enter bt_probe of_node
[ 12.622879@2] not get gpio_en
[ 12.625805@2] power on valid level is high[ 12.629707@2] bt: power_on_pin_OD = 0;
[ 12.633436@2] bt: power_off_flag = 1;
[ 12.637072@2] dis power down = 0;
[ 12.665906@2] BLASTER Driver Init
[ 12.667433@2] meson-saradc ff809000.saradc: set delay per tick to <1ms> by default.
[ 12.672430@2] meson-saradc ff809000.saradc: set ticks per period to <1> by default.
[ 12.681000@2] dmc_monitor_probe
[ 12.683753@2] aml_atvdemod_init: OK, atv demod version: V2.04.
[ 12.689062@2] defendkey ff630218.defendkey: Reserved memory is not enough!
[ 12.695826@2] defendkey: probe of ff630218.defendkey failed with error -22
[ 12.703176@2] usbcore: registered new interface driver snd-usb-audio
[ 12.710031@2] aml_codec_T9015 ff632000.t9015: aml_T9015_audio_codec_probe
[ 12.715776@2] T9015 acodec used by auge, tdmout:1
[ 12.721745@5] asoc debug: aml_audio_controller_probe-127
[ 12.726514@5] aml_tdm_platform_probe, tdm ID = 0, lane_cnt = 4
[ 12.731552@5] snd_tdm ff642000.audiobus:tdma: lane_mask_out = 0, lane_oe_mask_out = 0
[ 12.739425@5] aml_tdm_platform_probe(), share en = 1[ 12.744092@5] No channel mask node Channel_Mask
[ 12.748734@5] aml_tdm_platform_probe, tdm ID = 1, lane_cnt = 4
[ 12.754451@5] TDM id 1 samesource_sel:3
[ 12.758220@5] snd_tdm ff642000.audiobus:tdmb: lane_mask_out = 1, lane_oe_mask_out = 0
[ 12.766149@5] aml_tdm_platform_probe(), share en = 1[ 12.770785@5] No channel mask node Channel_Mask
[ 12.775389@5] aml_tdm_platform_probe, tdm ID = 2, lane_cnt = 4
[ 12.781112@5] snd_tdm ff642000.audiobus:tdmc: lane_mask_out = 0, lane_oe_mask_out = 0
[ 12.788999@5] aml_tdm_platform_probe(), share en = 1[ 12.793665@5] No channel mask node Channel_Mask
[ 12.798727@5] hdmitx: audio: aout notify format CT_PCM
[ 12.803292@5] aml_spdif_platform_probe, register soc platform
[ 12.809083@5] aml_spdif_platform_probe, register soc platform
[ 12.815089@5] audio_ddr_mngr: 0, irqs toddr 26, frddr 29
[ 12.820011@5] audio_ddr_mngr: 1, irqs toddr 27, frddr 30
[ 12.825295@5] audio_ddr_mngr: 2, irqs toddr 28, frddr 31
[ 12.830935@5] audiolocker_platform_probe
[ 12.835251@5] Register vad
[ 13.045901@5] aml_dai_spdif_probe
[ 13.047339@5] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
[ 13.052703@5] snd_tdm ff642000.audiobus:tdmb: ASoC: Failed to add I2SIn CLK: -16
[ 13.060068@5] aml_dai_tdm_probe, failed add snd tdm controls
[ 13.065702@5] asoc-aml-card auge_sound: control 2:0:0:I2SIn CLK:0 is already present
[ 13.073414@5] snd_tdm ff642000.audiobus:tdmc: ASoC: Failed to add I2SIn CLK: -16
[ 13.080779@5] aml_dai_tdm_probe, failed add snd tdm controls
[ 13.086414@5] aml_dai_spdif_probe
[ 13.089951@5] asoc-aml-card auge_sound: dit-hifi <-> SPDIF-B mapping ok
[ 13.096312@5] master_mode(1), binv(1), finv(0) out_skew(2), in_skew(3)
[ 13.103034@5] asoc-aml-card auge_sound: multicodec <-> TDM-A mapping ok
[ 13.109397@5] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3)
[ 13.116093@5] asoc-aml-card auge_sound: multicodec <-> TDM-B mapping ok
[ 13.122481@5] master_mode(1), binv(1), finv(1) out_skew(2), in_skew(3)
[ 13.129181@5] asoc-aml-card auge_sound: multicodec <-> TDM-C mapping ok
[ 13.135679@5] asoc-aml-card auge_sound: dit-hifi <-> SPDIF mapping ok
[ 13.143059@2] snd_card_add_kcontrols card:ffffffc07ec89818
[ 13.147438@2] effect_v2 is not init
[ 13.150896@2] Failed to add VAD controls
[ 13.154818@2] eq/drc v1 function enable
[ 13.185944@2] GACT probability NOT on
[ 13.187559@2] Mirror/redirect action on
[ 13.189371@2] u32 classifier
[ 13.192238@2] Actions configured
[ 13.195795@2] Netfilter messages via NETLINK v0.30.
[ 13.200761@2] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 13.206957@2] ctnetlink v0.93: registering with nfnetlink.
[ 13.212602@2] xt_time: kernel timezone is -0000
[ 13.216862@2] IPVS: Registered protocols (TCP, UDP)
[ 13.221781@2] IPVS: Connection hash table configured (size=4096, memory=64Kbytes)
[ 13.229200@2] IPVS: Creating netns size=1928 id=0
[ 13.233876@2] IPVS: ipvs loaded.
[ 13.237036@2] IPVS: [rr] scheduler registered.
[ 13.241508@2] ipip: IPv4 and MPLS over IPv4 tunneling driver
[ 13.247292@2] IPv4 over IPsec tunneling driver
[ 13.251732@2] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 13.257074@2] arp_tables: arp_tables: (C) 2002 David S. Miller
[ 13.262820@2] Initializing XFRM netlink socket
[ 13.267442@2] NET: Registered protocol family 10
[ 13.272289@2] mip6: Mobile IPv6
[ 13.274932@2] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 13.280801@2] sit: IPv6, IPv4 and MPLS over IPv4 tunneling driver
[ 13.286927@2] NET: Registered protocol family 17
[ 13.291133@2] NET: Registered protocol family 15
[ 13.295750@2] Bridge firewalling registered
[ 13.299917@2] Bluetooth: RFCOMM TTY layer initialized
[ 13.304909@2] Bluetooth: RFCOMM socket layer initialized
[ 13.310215@2] Bluetooth: RFCOMM ver 1.11
[ 13.314095@2] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 13.319549@2] Bluetooth: BNEP filters: protocol multicast
[ 13.324933@2] Bluetooth: BNEP socket layer initialized
[ 13.330038@2] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 13.336108@2] Bluetooth: HIDP socket layer initialized
[ 13.341224@2] l2tp_core: L2TP core driver, V2.0
[ 13.345735@2] l2tp_ppp: PPPoL2TP kernel driver, V2.0
[ 13.350666@2] l2tp_ip: L2TP IP encapsulation support (L2TPv3)
[ 13.356396@2] l2tp_netlink: L2TP netlink interface
[ 13.361166@2] l2tp_eth: L2TP ethernet pseudowire support (L2TPv3)
[ 13.367229@2] l2tp_debugfs: L2TP debugfs support
[ 13.371807@2] l2tp_ip6: L2TP IP encapsulation support for IPv6 (L2TPv3)
[ 13.378477@2] NET: Registered protocol family 35
[ 13.383022@2] Key type dns_resolver registered
[ 13.387987@2] Registered swp emulation handler
[ 13.391833@2] Registered cp15_barrier emulation handler
[ 13.397037@2] Registered setend emulation handler
[ 13.401982@2] registered taskstats version 1
[ 13.411200@2] edt_ft5x06 3-0038: probing for EDT FT5x06 I2C
[ 13.754053@2] edt_ft5x06 3-0038: touchscreen probe failed
[ 13.755973@3] dwc3 ff500000.dwc3: Configuration mismatch. dr_mode forced to host
[ 13.765217@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 13.768275@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1
[ 13.776258@3] xhci-hcd xhci-hcd.0.auto: hcc params 0x0228fe64 hci version 0x110 quirks 0x00010010
[ 13.784925@3] xhci-hcd xhci-hcd.0.auto: irq 15, io mem 0xff500000
[ 13.791257@3] hub 1-0:1.0: USB hub found
[ 13.794879@3] hub 1-0:1.0: 2 ports detected
[ 13.799173@3] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller
[ 13.804660@3] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2
[ 13.812482@3] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.
[ 13.820931@3] hub 2-0:1.0: USB hub found
[ 13.824601@3] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)
[ 13.831945@3] usb usb2: Unsupported the hub
[ 13.836263@3] rtc-hym8563 4-0051: no valid clock/calendar values available
[ 13.842881@3] rtc-hym8563 4-0051: hctosys: unable to read the hardware clock
[ 13.850091@3] dwc_otg: usb0: type: 2 speed: 0, config: 0, dma: 0, id: 0, phy: ffe09000, ctrl: 0
[ 13.958695@3] dwc_otg: Core Release: 3.30a
[ 13.960160@3] dwc_otg: Setting default values for core params
[ 13.964317@3] dwc_otg: curmode: 0, host_only: 0
[ 13.980965@3] dwc_otg: Using Buffer DMA mode
[ 13.982448@3] dwc_otg: OTG VER PARAM: 1, OTG VER FLAG: 1
[ 13.986343@3] dwc_otg: Working on port type = SLAVE
[ 13.991197@3] dwc_otg: Dedicated Tx FIFOs mode
[ 13.996682@3] input: adc_keypad as /devices/platform/adc_keypad/input/input4
[ 14.003112@3] bl: chip type/name: (5-g12a)
[ 14.006754@3] bl: key_valid: 0
[ 14.009880@3] bl: aml_bl_config_load from dts
[ 14.014083@3] bl: no backlight exist
[ 14.017629@3] aml-bl: probe of backlight failed with error -1
[ 14.023753@3] meson_cdev probe
[ 14.026432@3] meson_cdev index: 0
[ 14.029721@3] thermal thermal_zone0: binding zone soc_thermal with cdev thermal-cpufreq-0 failed:-22
[ 14.038818@3] meson_cdev index: 1
[ 14.042199@3] meson_cdev index: 2
[ 14.045360@3] cpucore_cooling_register, max_cpu_core_num:2
[ 14.050880@3] meson_cdev index: 3
[ 14.054121@3] cpucore_cooling_register, max_cpu_core_num:4
[ 14.059627@3] meson_cdev index: 4
[ 14.062882@3] meson_cdev index: 5
[ 14.066186@3] find tzd id: 0
[ 14.069098@3] find tzd id: 0
[ 14.071979@3] find tzd id: 0
[ 14.074813@3] meson_cdev probe done
[ 14.078305@3] gxbb_pm: enter meson_pm_probe!
[ 14.082474@3] gxbb_pm: meson_pm_probe done
[ 14.086915@3] ALSA device list:
[ 14.089645@3] #0: AML-AUGESOUND
[ 14.094924@3] Freeing unused kernel memory: 5504K
[ 14.129842@3] usb 1-1: new high-speed USB device number 2 using xhci-hcd
[ 14.292678@3] hub 1-1:1.0: USB hub found
[ 14.294240@3] hub 1-1:1.0: 4 ports detected
[ 14.401450@2] fb: osd[0] enable: 1 (khadas_init.sh)
[ 15.421410@0] fb: osd[1] enable: 0 (khadas_init.sh)
[ 16.517878@4] raid6: int64x1 gen() 1099 MB/s
[ 16.585837@4] raid6: int64x1 xor() 1002 MB/s
[ 16.653820@4] raid6: int64x2 gen() 1749 MB/s
[ 16.721823@4] raid6: int64x2 xor() 1280 MB/s
[ 16.789848@2] raid6: int64x4 gen() 2270 MB/s
[ 16.857840@4] raid6: int64x4 xor() 1569 MB/s
[ 16.925844@2] raid6: int64x8 gen() 2288 MB/s
[ 16.993844@5] raid6: int64x8 xor() 1562 MB/s
[ 17.061833@5] raid6: neonx1 gen() 2609 MB/s
[ 17.129823@5] raid6: neonx1 xor() 1638 MB/s
[ 17.197820@5] raid6: neonx2 gen() 3221 MB/s
[ 17.265830@5] raid6: neonx2 xor() 2461 MB/s
[ 17.333825@5] raid6: neonx4 gen() 3996 MB/s
[ 17.401818@5] raid6: neonx4 xor() 3159 MB/s
[ 17.469822@5] raid6: neonx8 gen() 4634 MB/s
[ 17.537825@5] raid6: neonx8 xor() 3444 MB/s
[ 17.539145@5] raid6: using algorithm neonx8 gen() 4634 MB/s
[ 17.543471@5] raid6: .... xor() 3444 MB/s, rmw enabled
[ 17.548585@5] raid6: using intx1 recovery algorithm
[ 17.553781@5] xor: measuring software checksum speed
[ 17.597819@5] 8regs : 7460.000 MB/sec
[ 17.637819@5] 8regs_prefetch: 6277.000 MB/sec
[ 17.677817@5] 32regs : 8580.000 MB/sec
[ 17.717818@5] 32regs_prefetch: 8350.000 MB/sec
[ 17.719053@5] xor: using function: 32regs (8580.000 MB/sec)
[ 17.757326@5] Btrfs loaded, crc32c=crc32c-generic, assert=on
[ 17.758945@5] BTRFS: selftest: sectorsize: 4096 nodesize: 4096
[ 17.764696@5] BTRFS: selftest: Running btrfs free space cache tests
[ 17.770939@5] BTRFS: selftest: Running extent only tests
[ 17.776216@5] BTRFS: selftest: Running bitmap only tests
[ 17.781503@5] BTRFS: selftest: Running bitmap and extent tests
[ 17.787312@5] BTRFS: selftest: Running space stealing from bitmap to extent
[ 17.794555@5] BTRFS: selftest: Free space cache tests finished
[ 17.800045@5] BTRFS: selftest: Running extent buffer operation tests
[ 17.806368@5] BTRFS: selftest: Running btrfs_split_item tests
[ 17.812113@5] BTRFS: selftest: Running extent I/O tests
[ 17.817288@5] BTRFS: selftest: Running find delalloc tests
[ 17.931844@5] BTRFS: selftest: Running extent buffer bitmap tests
[ 17.984379@5] BTRFS: selftest: Extent I/O tests finished
[ 17.985600@5] BTRFS: selftest: Running btrfs_get_extent tests
[ 17.991064@5] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 17.997577@5] BTRFS: selftest: Running outstanding_extents tests
[ 18.003565@5] BTRFS: selftest: Running qgroup tests
[ 18.008391@5] BTRFS: selftest: Qgroup basic add
[ 18.012926@5] BTRFS: selftest: Qgroup multiple refs test
[ 18.018227@5] BTRFS: selftest: Running free space tree tests
[ 18.045049@5] BTRFS: selftest: sectorsize: 4096 nodesize: 8192
[ 18.046463@5] BTRFS: selftest: Running btrfs free space cache tests
[ 18.052702@5] BTRFS: selftest: Running extent only tests
[ 18.057995@5] BTRFS: selftest: Running bitmap only tests
[ 18.063281@5] BTRFS: selftest: Running bitmap and extent tests
[ 18.069091@5] BTRFS: selftest: Running space stealing from bitmap to extent
[ 18.076331@5] BTRFS: selftest: Free space cache tests finished
[ 18.081820@5] BTRFS: selftest: Running extent buffer operation tests
[ 18.088146@5] BTRFS: selftest: Running btrfs_split_item tests
[ 18.093878@5] BTRFS: selftest: Running extent I/O tests
[ 18.099065@5] BTRFS: selftest: Running find delalloc tests
[ 18.213701@5] BTRFS: selftest: Running extent buffer bitmap tests
[ 18.266245@5] BTRFS: selftest: Extent I/O tests finished
[ 18.267428@5] BTRFS: selftest: Running btrfs_get_extent tests
[ 18.272899@5] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 18.279409@5] BTRFS: selftest: Running outstanding_extents tests
[ 18.285397@5] BTRFS: selftest: Running qgroup tests
[ 18.290220@5] BTRFS: selftest: Qgroup basic add
[ 18.294757@5] BTRFS: selftest: Qgroup multiple refs test
[ 18.300062@5] BTRFS: selftest: Running free space tree tests
[ 18.326899@5] BTRFS: selftest: sectorsize: 4096 nodesize: 16384
[ 18.328294@5] BTRFS: selftest: Running btrfs free space cache tests
[ 18.334543@5] BTRFS: selftest: Running extent only tests
[ 18.339836@5] BTRFS: selftest: Running bitmap only tests
[ 18.345121@5] BTRFS: selftest: Running bitmap and extent tests
[ 18.350931@5] BTRFS: selftest: Running space stealing from bitmap to extent
[ 18.358171@5] BTRFS: selftest: Free space cache tests finished
[ 18.363663@5] BTRFS: selftest: Running extent buffer operation tests
[ 18.369986@5] BTRFS: selftest: Running btrfs_split_item tests
[ 18.375719@5] BTRFS: selftest: Running extent I/O tests
[ 18.380906@5] BTRFS: selftest: Running find delalloc tests
[ 18.495412@5] BTRFS: selftest: Running extent buffer bitmap tests
[ 18.547921@5] BTRFS: selftest: Extent I/O tests finished
[ 18.549047@5] BTRFS: selftest: Running btrfs_get_extent tests
[ 18.554513@5] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 18.561023@5] BTRFS: selftest: Running outstanding_extents tests
[ 18.567010@5] BTRFS: selftest: Running qgroup tests
[ 18.571837@5] BTRFS: selftest: Qgroup basic add
[ 18.576373@5] BTRFS: selftest: Qgroup multiple refs test
[ 18.581677@5] BTRFS: selftest: Running free space tree tests
[ 18.608519@5] BTRFS: selftest: sectorsize: 4096 nodesize: 32768
[ 18.609986@5] BTRFS: selftest: Running btrfs free space cache tests
[ 18.616227@5] BTRFS: selftest: Running extent only tests
[ 18.621519@5] BTRFS: selftest: Running bitmap only tests
[ 18.626808@5] BTRFS: selftest: Running bitmap and extent tests
[ 18.632616@5] BTRFS: selftest: Running space stealing from bitmap to extent
[ 18.639855@5] BTRFS: selftest: Free space cache tests finished
[ 18.645343@5] BTRFS: selftest: Running extent buffer operation tests
[ 18.651672@5] BTRFS: selftest: Running btrfs_split_item tests
[ 18.657403@5] BTRFS: selftest: Running extent I/O tests
[ 18.662589@5] BTRFS: selftest: Running find delalloc tests
[ 18.777021@5] BTRFS: selftest: Running extent buffer bitmap tests
[ 18.829510@5] BTRFS: selftest: Extent I/O tests finished
[ 18.830627@5] BTRFS: selftest: Running btrfs_get_extent tests
[ 18.836085@5] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 18.842609@5] BTRFS: selftest: Running outstanding_extents tests
[ 18.848583@5] BTRFS: selftest: Running qgroup tests
[ 18.853404@5] BTRFS: selftest: Qgroup basic add
[ 18.857943@5] BTRFS: selftest: Qgroup multiple refs test
[ 18.863247@5] BTRFS: selftest: Running free space tree tests
[ 18.890127@5] BTRFS: selftest: sectorsize: 4096 nodesize: 65536
[ 18.891558@5] BTRFS: selftest: Running btrfs free space cache tests
[ 18.897807@5] BTRFS: selftest: Running extent only tests
[ 18.903100@5] BTRFS: selftest: Running bitmap only tests
[ 18.908389@5] BTRFS: selftest: Running bitmap and extent tests
[ 18.914196@5] BTRFS: selftest: Running space stealing from bitmap to extent
[ 18.921435@5] BTRFS: selftest: Free space cache tests finished
[ 18.926924@5] BTRFS: selftest: Running extent buffer operation tests
[ 18.933250@5] BTRFS: selftest: Running btrfs_split_item tests
[ 18.938985@5] BTRFS: selftest: Running extent I/O tests
[ 18.944169@5] BTRFS: selftest: Running find delalloc tests
[ 19.058920@5] BTRFS: selftest: Running extent buffer bitmap tests
[ 19.111396@5] BTRFS: selftest: Extent I/O tests finished
[ 19.112509@5] BTRFS: selftest: Running btrfs_get_extent tests
[ 19.117977@5] BTRFS: selftest: Running hole first btrfs_get_extent test
[ 19.124488@5] BTRFS: selftest: Running outstanding_extents tests
[ 19.130475@5] BTRFS: selftest: Running qgroup tests
[ 19.135301@5] BTRFS: selftest: Qgroup basic add
[ 19.139835@5] BTRFS: selftest: Qgroup multiple refs test
[ 19.145145@5] BTRFS: selftest: Running free space tree tests
[ 24.375039@0] EXT4-fs (mmcblk0p6): recovery complete
[ 24.378752@0] EXT4-fs (mmcblk0p6): mounted filesystem with writeback data mode. Opts: data=writeback
[ 24.534360@0] systemd[1]: System time before build time, advancing clock.
[ 24.542159@0] cgroup: cgroup2: unknown option "nsdelegate"
[ 24.555486@0] systemd[1]: systemd 237 running in system mode. (+PAM +AUDIT +SELINUX +IMA +APPARMOR +SMACK +SYSVINIT +UTMP +LIBCRYPTSETUP +GCRYPT +GNUTLS +ACL +XZ +LZ4 +SECCOMP +BLKID +ELFUTILS +KMOD -IDN2 +IDN -PCRE2 default-hierarchy=hybrid)
[ 24.578286@0] systemd[1]: Detected architecture arm64.
[ 24.591080@2] systemd[1]: Set hostname to <Khadas>.
[ 24.625723@2] meson_uart ff803000.serial: ttyS0 use xtal(24M) 24000000 change 115200 to 115200
[ 24.683553@2] systemd[1]: File /lib/systemd/system/systemd-journald.service:36 configures an IP firewall (IPAddressDeny=any), but the local system does not support BPF/cgroup based firewalling.
[ 24.696738@2] systemd[1]: Proceeding WITHOUT firewalling in effect! (This warning is only shown for the first loaded unit using IP firewalling.)
[ 24.763300@2] systemd[1]: Reached target Remote File Systems.
[ 24.767066@2] systemd[1]: Reached target Swap.
[ 24.771572@2] systemd[1]: Set up automount Arbitrary Executable File Formats File System Automount Point.
[ 24.780936@2] systemd[1]: Reached target System Time Synchronized.
[ 24.787003@2] systemd[1]: Reached target User and Group Name Lookups.
[ 24.882713@4] dhd_module_init: in Dongle Host Driver, version 1.579.77.41.10 (r)
[ 24.882717@4] ======== dhd_wlan_init_plat_data ========
[ 24.882720@4] dhd_wlan_init_gpio: WL_HOST_WAKE=-1, oob_irq=103, oob_irq_flags=0x418
[ 24.882721@4] dhd_wlan_init_gpio: WL_REG_ON=-1
[ 24.882722@4] dhd_wifi_platform_load: Enter
[ 24.882766@4] Power-up adapter 'DHD generic adapter'
[ 24.882767@4] wifi_platform_set_power = 1
[ 24.882769@4] ======== PULL WL_REG_ON(-1) HIGH! ========
[ 24.882782@4] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
[ 24.906545@1] EXT4-fs (mmcblk0p6): re-mounted. Opts: commit=600,errors=remount-ro
[ 25.018978@2] systemd-journald[2563]: Received request to flush runtime journal from PID 1
[ 25.082808@4] aml_wifi wifi: [extern_wifi_set_enable] WIFI Enable! 482
[ 25.107649@2] IPVS: Creating netns size=1928 id=1
[ 25.241386@5] zram: Added device: zram0
[ 25.248180@2] zram: Added device: zram1
[ 25.255460@3] zram: Added device: zram2
[ 25.261534@3] zram: Added device: zram3
[ 25.270363@3] zram: Added device: zram4
[ 25.276333@3] zram: Added device: zram5
[ 25.277028@4] amlvideo2.0 cma memory is cfc00000 , size is 1800000
[ 25.277630@4] amlvideo2.0 cma memory release succeed
[ 25.304224@5] fw_module_init@main_kernel_juno_v4l2.c:772 GENERIC(ERR) :Juno isp fw_module_init
[ 25.304225@5]
[ 25.304439@5] isp_module_check@main_kernel_juno_v4l2.c:542 GENERIC(ERR) :isp efuse value: ff630038 4000
[ 25.304440@5]
[ 25.304490@5] isp_platform_probe@main_kernel_juno_v4l2.c:580 GENERIC(ERR) :Juno isp irq = 60, flags = 0x404 !
[ 25.304490@5]
[ 25.304494@5] isp_platform_probe@main_kernel_juno_v4l2.c:590 GENERIC(ERR) :Juno isp address = 0xff140000, end = 0xff17ffff !
[ 25.304494@5]
[ 25.311253@5] amlvideo2.1 cma memory is cfc00000 , size is 1800000
[ 25.311529@5] amlvideo2.1 cma memory release succeed
[ 25.313401@4] arm_isp ff140000.isp: assigned reserved memory node linux,isp_cma
[ 25.313419@4] isp_platform_probe@main_kernel_juno_v4l2.c:609 GENERIC(ERR) :Success to get link device: isp-sc
[ 25.313420@4]
[ 25.313430@4] AM_SC: am_sc_parse_dt: rs idx info: name: isp_sc
[ 25.313442@4] AM_SC: am_sc_parse_dt:rs info: irq: 59
[ 25.313546@4] isp_platform_probe@main_kernel_juno_v4l2.c:624 GENERIC(ERR) :isp init clock is 666 MHZ
[ 25.313546@4]
[ 25.313584@4] isp_platform_probe@main_kernel_juno_v4l2.c:637 GENERIC(ERR) :mipi init clock is 199 MHZ
[ 25.313584@4]
[ 25.320987@0] interrupt comes in (irq = 60) without app handler, status: 0x200, pusle mode:0
[ 25.326750@4] isp_platform_probe@main_kernel_juno_v4l2.c:650 GENERIC(ERR) :register v4l2 driver. result 0.
[ 25.326753@4] isp_platform_probe@main_kernel_juno_v4l2.c:659 GENERIC(ERR) :--------------------------------
[ 25.326756@4] isp_platform_probe@main_kernel_juno_v4l2.c:660 GENERIC(ERR) :Register 3 subdevices
[ 25.326759@4] isp_platform_probe@main_kernel_juno_v4l2.c:661 GENERIC(ERR) :--------------------------------
[ 25.326774@4] isp_platform_probe@main_kernel_juno_v4l2.c:685 GENERIC(ERR) :Init finished. async register notifier result 0. Waiting for subdevices
[ 25.331640@1] mali ffe40000.bifrost: Continuing without Mali regulator control
[ 25.331756@1] mali ffe40000.bifrost: max pp is 2
[ 25.331760@1] mali ffe40000.bifrost: set min pp to default 1
[ 25.331762@1] mali ffe40000.bifrost: min pp is 1
[ 25.331766@1] mali ffe40000.bifrost: set min clk default to 0
[ 25.331769@1] mali ffe40000.bifrost: min clk is 0
[ 25.331785@1] mali ffe40000.bifrost: hiu io source 0xffffff8010538000
[ 25.331795@1] mali ffe40000.bifrost: hiu io source 0xffffff801053a000
[ 25.331799@1] mali ffe40000.bifrost: num of pp used most of time 1
[ 25.331802@1] mali ffe40000.bifrost: clock dvfs cfg table size is 6
[ 25.331833@1] mali ffe40000.bifrost: max clk set 4
[ 25.331835@1] mali ffe40000.bifrost: max clk is 4
[ 25.331839@1] mali ffe40000.bifrost: turbo clk set to 5
[ 25.331841@1] mali ffe40000.bifrost: turbo clk is 5
[ 25.331845@1] mali ffe40000.bifrost: default clk set to 4
[ 25.331848@1] mali ffe40000.bifrost: default clk is 4
[ 25.331853@1] mali ffe40000.bifrost: ====================0====================
[ 25.331853@1] clk_freq= 285714285, clk_parent=fclk_div7, voltage=1150, keep_count=5, threshod=<100 190>, clk_sample=285
[ 25.331858@1] mali ffe40000.bifrost: ====================1====================
[ 25.331858@1] clk_freq= 400000000, clk_parent=fclk_div5, voltage=1150, keep_count=5, threshod=<152 207>, clk_sample=400
[ 25.331862@1] mali ffe40000.bifrost: ====================2====================
[ 25.331862@1] clk_freq= 500000000, clk_parent=fclk_div4, voltage=1150, keep_count=5, threshod=<180 220>, clk_sample=500
[ 25.331867@1] mali ffe40000.bifrost: ====================3====================
[ 25.331867@1] clk_freq= 666666666, clk_parent=fclk_div3, voltage=1150, keep_count=5, threshod=<210 236>, clk_sample=666
[ 25.331871@1] mali ffe40000.bifrost: ====================4====================
[ 25.331871@1] clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800
[ 25.331875@1] mali ffe40000.bifrost: ====================5====================
[ 25.331875@1] clk_freq= 800000000, clk_parent=fclk_div2p5, voltage=1150, keep_count=5, threshod=<230 255>, clk_sample=800
[ 25.331878@1] mali ffe40000.bifrost: clock dvfs table size is 6
[ 25.332000@1] mali_plat=ffffff800236e620
[ 25.332333@1] find tzd id: 0
[ 25.332400@1] gpu cooling register okay with err=0
[ 25.332600@1] find tzd id: 0
[ 25.332619@1] gpu core cooling register okay with err=0
[ 25.332649@1] shader_present=3, tiler_present=1, l2_present=1
[ 25.332734@1] Mali_pwr_on:gpu_irq : 200
[ 25.332986@1] mali ffe40000.bifrost: GPU identified as 0x2 arch 7.2.1 r0p0 status 0
[ 25.333292@1] mali ffe40000.bifrost: Using coherency mode 0 set from dtb
[ 25.335654@4] mali ffe40000.bifrost: Probed as mali0
[ 25.406153@4] zram1: detected capacity change from 0 to 268435456
[ 25.637196@4] Adding 262140k swap on /dev/zram1. Priority:5 extents:1 across:262140k SS
[ 25.638181@5] zram2: detected capacity change from 0 to 268435456
[ 25.644924@4] Adding 262140k swap on /dev/zram2. Priority:5 extents:1 across:262140k SS
[ 25.645815@5] zram3: detected capacity change from 0 to 268435456
[ 25.652318@4] Adding 262140k swap on /dev/zram3. Priority:5 extents:1 across:262140k SS
[ 25.653189@5] zram4: detected capacity change from 0 to 268435456
[ 25.657976@4] wifi_platform_bus_enumerate device present 1
[ 25.657979@4] ======== Card detection to detect SDIO card! ========
[ 25.659195@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 25.659197@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
[ 25.659912@5] Adding 262140k swap on /dev/zram4. Priority:5 extents:1 across:262140k SS
[ 25.660237@0] meson-mmc: sdio: resp_timeout,vstat:0xa1ff2800,virqc:3fff
[ 25.660238@0] meson-mmc: sdio: err: wait for irq service, bus_fsm:0x8
[ 25.665076@0] meson-mmc: sdio: resp_timeout,vstat:0x9dff0800,virqc:3fff
[ 25.665078@0] meson-mmc: sdio: err: wait for desc write back, bus_fsm:0x7
[ 25.667688@4] meson-mmc: actual_clock :0, HHI_nand: 0x80
[ 25.667690@4] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 25.685868@4] meson-mmc: actual_clock :400000, HHI_nand: 0x80
[ 25.685870@4] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x1000023c
[ 25.704753@4] sdio: queuing unknown CIS tuple 0x80 (2 bytes)
[ 25.707465@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 25.710189@4] sdio: queuing unknown CIS tuple 0x80 (3 bytes)
[ 25.715086@4] sdio: queuing unknown CIS tuple 0x80 (7 bytes)
[ 25.720998@4] sdio: queuing unknown CIS tuple 0x81 (9 bytes)
[ 25.812554@4] meson-aml-mmc ffe03000.sdio: divider requested rate 200000000 != actual rate 199999997: ret=0
[ 25.812558@4] meson-mmc: actual_clock :199999997, HHI_nand: 0x80
[ 25.812559@4] meson-mmc: [meson_mmc_clk_set_rate_v3] after clock: 0x10000245
[ 25.812562@4] meson-mmc: Data 1 aligned delay is 0
[ 25.812564@4] meson-mmc: sdio: clk 199999997 tuning start
[ 25.812591@4] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 25.813476@4] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 25.814309@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.815117@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.815920@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.815922@4] meson-mmc: [prev_map] fixed_adj_win_map:30
[ 25.815923@4] meson-mmc: [0]=0
[ 25.815924@4] meson-mmc: [1]=1
[ 25.815925@4] meson-mmc: [2]=1
[ 25.815925@4] meson-mmc: [3]=1
[ 25.815926@4] meson-mmc: [4]=1
[ 25.815927@4] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 25.815929@4] meson-mmc: step:4, delay1:0x4104104, delay2:0x4004104
[ 25.815951@4] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 25.816760@4] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 25.817570@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.818453@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.819316@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.819318@4] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 25.819319@4] meson-mmc: step:8, delay1:0x8208208, delay2:0x8008208
[ 25.820209@4] meson-mmc: sdio: rx_tuning_result[0] = 40
[ 25.821020@4] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 25.821862@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.822927@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.823960@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.823962@4] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 25.823965@4] meson-mmc: step:12, delay1:0xc30c30c, delay2:0xc00c30c
[ 25.824777@4] meson-mmc: sdio: rx_tuning_result[0] = 40
[ 25.825579@4] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 25.826476@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.827336@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.828171@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.828172@4] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 25.828174@4] meson-mmc: step:16, delay1:0x10410410, delay2:0x10010410
[ 25.828984@4] meson-mmc: sdio: rx_tuning_result[0] = 40
[ 25.829788@4] meson-mmc: sdio: rx_tuning_result[1] = 40
[ 25.830679@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.831561@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.832439@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.832440@4] meson-mmc: [_find_fixed_adj_valid_win]retry test fixed adj...
[ 25.832442@4] meson-mmc: step:20, delay1:0x14514514, delay2:0x14014514
[ 25.833375@4] meson-mmc: sdio: rx_tuning_result[0] = 40
[ 25.833399@4] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 25.834321@4] meson-mmc: sdio: rx_tuning_result[2] = 40
[ 25.835197@4] meson-mmc: sdio: rx_tuning_result[3] = 40
[ 25.836078@4] meson-mmc: sdio: rx_tuning_result[4] = 40
[ 25.836079@4] meson-mmc: [>>>>>>>>bitmap_xor_dst] fixed_adj_win_map:2
[ 25.836080@4] meson-mmc: [0]=0
[ 25.836081@4] meson-mmc: [1]=1
[ 25.836082@4] meson-mmc: [2]=0
[ 25.836083@4] meson-mmc: [3]=0
[ 25.836083@4] meson-mmc: [4]=0
[ 25.836084@4] meson-mmc: [_find_fixed_adj_valid_win] fir_adj:1
[ 25.836086@4] meson-mmc: [>>>>>>>>prev_map_range] fixed_adj_win_map:495
[ 25.836087@4] meson-mmc: [1]=1
[ 25.836087@4] meson-mmc: [2]=1
[ 25.836088@4] meson-mmc: [3]=1
[ 25.836089@4] meson-mmc: [4]=1
[ 25.836089@4] meson-mmc: [0]=0
[ 25.836091@4] meson-mmc: left:3, right:0, mid:4, size:4
[ 25.836093@4] meson-mmc: step:0, delay1:0x0, delay2:0x0
[ 25.836095@4] meson-mmc: sdio: sd_emmc_regs->gclock=0x10000245,sd_emmc_regs->gadjust=0x32000
[ 25.836096@4] meson-mmc: delay1:0x0, delay2:0x0
[ 25.839857@4] sdio: new ultra high speed SDR104 SDIO card at address 0001
[ 25.840091@2] sdio: clock 199999997, 4-bit-bus-width
[ 25.840091@2]
[ 25.840091@2] meson-mmc: [sdio_reinit] finish
[ 25.856320@2] bcmsdh_register: register client driver
[ 25.856420@2] bcmsdh_sdmmc_probe: Enter num=1
[ 25.856485@2] bcmsdh_sdmmc_probe: Enter num=2
[ 25.856486@2] bus num (host idx)=2, slot num (rca)=1
[ 25.856488@2] found adapter info 'DHD generic adapter'
[ 25.856492@2] Wifi: bcmdhd_mem_prealloc: sectoin 3, size 139264
[ 25.856509@2] alloc static buf at ffffffc09a540000!
[ 25.856511@2] Wifi: bcmdhd_mem_prealloc: sectoin 4, size 0
[ 25.856561@2] sdioh_attach: set sd_f2_blocksize 256
[ 25.856609@2] sdioh_attach: sd clock rate = 0
[ 25.856925@2] dhdsdio_probe : no mutex held. set lock
[ 25.857038@5] F1 signature read @0x18000000=0x17294359
[ 25.860698@2] F1 signature OK, socitype:0x1 chip:0x4359 rev:0x9 pkg:0x2
[ 25.861296@2] DHD: dongle ram size is set to 917504(orig 917504) at 0x160000
[ 25.861350@2] Wifi: bcmdhd_mem_prealloc: sectoin 7, size 30432
[ 25.861361@2] dhd_conf_set_chiprev: chip=0x4359, chiprev=9
[ 25.861394@2] Wifi: bcmdhd_mem_prealloc: sectoin 0, size 10320
[ 25.861414@2] CFG80211-ERROR) wl_setup_wiphy : Registering Vendor80211
[ 25.861573@2] Wifi: bcmdhd_mem_prealloc: sectoin 5, size 65536
[ 25.861696@4] CFG80211-ERROR) wl_init_prof : wl_init_prof: No profile
[ 25.861762@4] wl_escan_attach: Enter
[ 25.861764@4] Wifi: bcmdhd_mem_prealloc: sectoin 19, size 67488
[ 25.861779@4] wl_escan_init: Enter
[ 25.861824@4] tsk Enter, tsk = 0xffffffc09a5d0198
[ 25.861847@2] wl_create_event_handler(): thread:wl_escan_handler:b17 started
[ 25.861851@2] Wifi: bcmdhd_mem_prealloc: sectoin 20, size 65536
[ 25.861860@2] Wifi: bcmdhd_mem_prealloc: sectoin 21, size 65536
[ 25.861867@2] Wifi: bcmdhd_mem_prealloc: sectoin 22, size 65536
[ 25.861875@2] Wifi: bcmdhd_mem_prealloc: sectoin 23, size 65536
[ 25.861930@4] dhd_attach(): thread:dhd_watchdog_thread:b18 started
[ 25.861976@2] dhd_attach(): thread:dhd_dpc:b19 started
[ 25.862010@4] dhd_attach(): thread:dhd_rxf:b1a started
[ 25.862014@4] dhd_deferred_work_init: work queue initialized
[ 25.862016@4] dhd_tcpack_suppress_set: TCP ACK Suppress mode 0 -> mode 2
[ 25.862023@4] Wifi: bcmdhd_mem_prealloc: sectoin 1, size 10300
[ 25.862025@4] Wifi: bcmdhd_mem_prealloc: sectoin 2, size 65536
[ 25.862035@4] dhd_bus_set_default_min_res_mask: Unhandled chip id
[ 25.862264@4] sdioh_cis_read: func_cis_ptr[0]=0x10ac
[ 25.874516@2] Dongle Host Driver, version 1.579.77.41.10 (r)
[ 25.874814@2] wl_ext_iapsta_attach_netdev: ifidx=0, bssidx=0
[ 25.874817@2] Register interface [wlan0] MAC: 18:93:7f:aa:63:b8
[ 25.874817@2]
[ 25.874866@2] dhd_tcpack_suppress_set: TCP ACK Suppress mode 2 -> mode 0
[ 25.874872@2] dhd_wl_ioctl: returning as busstate=0
[ 25.874875@2] dhd_dbg_detach_pkt_monitor, 2204
[ 25.874878@2] dhd_bus_devreset: == Power OFF ==
[ 25.875140@2] bcmsdh_oob_intr_unregister: Enter
[ 25.875141@2] bcmsdh_oob_intr_unregister: irq is not registered
[ 25.875145@2] dhd_txglom_enable: enable 0
[ 25.875147@2] dhd_conf_set_txglom_params: txglom_mode=copy
[ 25.875148@2] dhd_conf_set_txglom_params: txglomsize=0, deferred_tx_len=0
[ 25.875149@2] dhd_conf_set_txglom_params: txinrx_thres=128, dhd_txminmax=-1
[ 25.875150@2] dhd_conf_set_txglom_params: tx_max_offset=0, txctl_tmo_fix=300
[ 25.875152@2] dhd_bus_devreset: WLAN OFF DONE
[ 25.875200@2] wifi_platform_set_power = 0
[ 25.875202@2] ======== PULL WL_REG_ON(-1) LOW! ========
[ 25.875211@2] aml_wifi wifi: [extern_wifi_set_enable] WIFI Disable! 482
[ 26.075224@2] dhdsdio_probe : the lock is released.
[ 26.075291@2] dhd_module_init: Exit err=0
[ 26.125727@2] No find node.
[ 26.125731@2] register clk_set_setting cpu[46]
[ 26.140962@2] dhd_ioctl_entry: Interface is down
[ 26.146642@2] Registered firmware driver success.
[ 26.147203@2] Try to load video/h264_enc.bin ...
[ 26.164504@4] load firmware size : 76288, Name : video/h264_enc.bin.
[ 26.164520@4] the fw pack ver v0.0 is too lower.
[ 26.164522@4] it may work abnormally so need to be update in time.
[ 26.164986@4] Try to load video/video_ucode.bin ...
[ 26.227706@2] load firmware size : 1706240, Name : video/video_ucode.bin.
[ 26.227821@2] the fw pack ver v0.2 is too lower.
[ 26.227822@2] it may work abnormally so need to be update in time.
[ 26.280593@2] Amlogic A/V streaming port init
[ 26.283871@2] get gate demux control ok ffffffc0995b35c0
[ 26.283880@2] get gate parser_top control ok ffffffc0995b3640
[ 26.283899@2] get gate vdec control ok ffffffc0995b36c0
[ 26.283903@2] get gate clk_81 control failed (null)
[ 26.283926@2] get gate clk_vdec_mux control ok ffffffc0995b3740
[ 26.283950@2] get gate clk_hcodec_mux control ok ffffffc0995b37c0
[ 26.283977@2] get gate clk_hevc_mux control ok ffffffc0995b3840
[ 26.284009@2] get gate clk_hevcb_mux control ok ffffffc0995b38c0
[ 26.284022@2] get gate ahbarb0 control ok ffffffc0995b3940
[ 26.284024@2] get gate asyncfifo control failed (null)
[ 26.319548@2] ammvdec_h264 module init
[ 26.374619@2] ammvdec_mpeg12 module init
[ 26.390273@2] ammvdec_mpeg4_driver_init_module
[ 26.469914@2] amvenc_avc_probe -- reserved memory config fail.
[ 26.469918@2] amvenc_avc - cma memory pool size: 60 MB
[ 26.469935@2] encode_wq_init.
[ 26.469939@2] encode start monitor.
[ 26.470021@2] encode workqueue monitor start.
[ 26.481419@2] vpu_init
[ 26.481589@2] vpu_probe
[ 26.481590@2] HevcEnc reserved memory config fail.
[ 26.481592@2] HevcEnc - cma memory pool size: 64 MB
[ 26.481612@2] HevcEnc - wave420l_irq: 51
[ 26.481672@2] vpu base address get from platform driver physical base addr=0xff610000, virtual base=0xffffff801135c000
[ 26.481792@2] success to probe vpu device with video memory from cma
[ 26.517290@2] reg resource 2, start: ff63c10c,end: ff63c10f
[ 26.517292@2] reg resource 3, start: ff63c110,end: ff63c113
[ 26.517293@2] reg resource 4, start: ffd01088,end: ffd0108b
[ 26.517295@2] reg resource NN_CLK, start: ff63c1c8,end: ff63c1cb
[ 26.517296@2] npu_version: 2
[ 26.517343@2] galcore irq number is 38.
[ 26.517345@2] Galcore version 6.4.0.229426
[ 26.560096@2] iq name from dts config is ----> os08a10
[ 26.560102@2] get_cali_name_id@soc_iq.c:168 SUBDEV_IQ(ERR) :get_calibrations_os08a10
[ 26.560102@2]
[ 26.560111@2] acamera_camera_async_bound@main_kernel_juno_v4l2.c:133 GENERIC(ERR) :bound called with sd 0x2a43400, asd 0x22bca68, sd->dev 0x9b2a0810, name SocCalibrations
[ 26.560116@2] soc_iq_probe@soc_iq.c:276 SUBDEV_IQ(ERR) :register v4l2 IQ device. result 0, sd 0x2a43400 sd->dev 0x9b2a0810
[ 26.570845@2] acamera_soc_lens_init@soc_lens.c:221 GENERIC(INFO) :Lens subdevice init
[ 26.571173@2] acamera_camera_async_bound@main_kernel_juno_v4l2.c:133 GENERIC(ERR) :bound called with sd 0x2a95480, asd 0x22bca90, sd->dev 0x9999cc10, name SocLens
[ 26.571179@2] soc_lens_probe@soc_lens.c:193 GENERIC(INFO) :register v4l2 lens device. result 0, sd 0x2a95480 sd->dev 0x9999cc10
[ 26.593272@2] acamera_camera_sensor_init@soc_sensor.c:564 GENERIC(ERR) :Sensor subdevice init
[ 26.593548@2] config sensor os08a10 driver.
[ 26.593573@2] ir_cut_get_named_gpio@soc_sensor.c:477 GENERIC(ERR) :ir cut gpio count = 1
[ 26.593573@2]
[ 26.593584@2] ir_cut_get_named_gpio@soc_sensor.c:482 GENERIC(ERR) :ir cut gpio name [0] = 404
[ 26.593585@2]
[ 26.593586@2] sensor bsp init
[ 26.593594@2] acamera_camera_async_bound@main_kernel_juno_v4l2.c:133 GENERIC(ERR) :bound called with sd 0x2ad9d98, asd 0x22bcab8, sd->dev 0x9b2a0410, name SocSensor
[ 26.593598@2] acamera_camera_async_complete@main_kernel_juno_v4l2.c:187 GENERIC(ERR) :complete called
[ 26.593601@2] acamera_camera_async_complete@main_kernel_juno_v4l2.c:189 GENERIC(ERR) :starting V4L2 firmware
[ 26.594453@5] isp_v4l2_ctrl_s_ctrl_standard@isp-v4l2-ctrl.c:43 GENERIC(ERR) :Control - id:0x980900, val:128, is_int:1, min:0, max:255.
[ 26.594454@5]
[ 26.594458@5] isp_fw_do_set_brightness@fw-interface.c:916 GENERIC(ERR) :ISP FW not inited yet
[ 26.595944@2] camera_ioctl@soc_sensor.c:251 GENERIC(ERR) :Failed to process camera_ioctl. Sensor is not initialized yet. camera_init must be called before
[ 26.596626@0] soc_lens_ioctl@soc_lens.c:100 GENERIC(ERR) :Failed to process lens_ioctl. Lens is not initialized yet. lens_init must be called before
[ 26.601844@4] acamera_init@acamera.c:299 GENERIC(ERR) :Success get product id: 0x00000a62
[ 26.601845@4]
[ 26.603182@5] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:104 GENERIC(ERR) :Requested a pointer to the subdev with a name SocSensor
[ 26.603188@5] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:111 GENERIC(ERR) :Return subdev pointer 0x2ad9d98
[ 26.603195@5] pwr_enable: get_named_gpio power-enable fail
[ 26.603196@5] set power fail
[ 26.613981@5] isp init clock is 24 MHZ
[ 26.614233@5] reset init
[ 26.614283@5] arm_sensor_i2c_probe: start to probe
[ 26.614286@5] arm_sensor_i2c_probe:arm isp slave addr 0x6c, rtn 0
[ 26.614288@5] arm_sensor_i2c_probe:arm reg_addr_type 2, rtn 0
[ 26.614289@5] arm_sensor_i2c_probe:arm reg_data_type 1, rtn 0
[ 26.614313@5] arm_sensor_i2c_probe: success get link device:phy-csi
[ 26.614323@5] AM_MIPI: am_mipi_parse_dt: rs idx 0 info: name: csi2_phy0
[ 26.614362@5] AM_MIPI: am_mipi_parse_dt: rs idx 1 info: name: csi2_phy1
[ 26.614367@5] AM_MIPI: am_mipi_parse_dt: rs idx 2 info: name: aphy_reg
[ 26.614378@5] AM_MIPI: am_mipi_parse_dt: rs idx 3 info: name: csi0_host
[ 26.614382@5] AM_MIPI: am_mipi_parse_dt: rs idx 4 info: name: csi1_host
[ 26.614393@5] AM_MIPI: am_mipi_parse_dt: rs idx 0 info: irq 62
[ 26.614398@5] AM_MIPI: am_mipi_parse_dt: rs idx 1 info: irq 63
[ 26.614411@5] AM_MIPI: am_mipi_parse_dt:Success to get link device: isp-adapter
[ 26.614416@5] AM_ADAP: am_adap_parse_dt: rs idx info: name: adapter
[ 26.614424@5] AM_ADAP: am_adap_parse_dt:rs info: irq: 61
[ 26.614468@5] platform ff650000.isp-adapter: assigned reserved memory node linux,adapt_cma
[ 26.614470@5] AM_ADAP: adapter alloc 48M memory
[ 26.614531@5] system_i2c_init:success to add i2c driver
[ 26.614665@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.614670@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.614799@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.614802@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.614930@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.614933@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.614937@5] sensor_get_id@OV08a10_drv.c:366 GENERIC(ERR) :sensor_get_id: Failed to read sensor id
[ 26.614937@5]
[ 26.617154@5] sensor_init_ov08a10@OV08a10_drv.c:665 GENERIC(ERR) :sensor_init_ov08a10: Success subdev init
[ 26.617155@5]
[ 26.617158@5] camera_init@soc_sensor.c:216 GENERIC(INFO) :Sensor has been initialized for ctx:0
[ 26.617159@5]
[ 26.617165@5] camera_ioctl@soc_sensor.c:430 GENERIC(ERR) :get isp_seq_num = 0
[ 26.617166@5]
[ 26.617172@5] sensor_print_params@V4L2_drv.c:63 GENERIC(ERR) :SOC SENSOR PARAMETERS
[ 26.617175@5] sensor_print_params@V4L2_drv.c:64 GENERIC(ERR) :pixels_per_line: 0
[ 26.617178@5] sensor_print_params@V4L2_drv.c:65 GENERIC(ERR) :again_log2_max: 2097152
[ 26.617180@5] sensor_print_params@V4L2_drv.c:66 GENERIC(ERR) :dgain_log2_max: 0
[ 26.617183@5] sensor_print_params@V4L2_drv.c:67 GENERIC(ERR) :again_accuracy: 0
[ 26.617186@5] sensor_print_params@V4L2_drv.c:68 GENERIC(ERR) :integration_time_min: 0
[ 26.617188@5] sensor_print_params@V4L2_drv.c:69 GENERIC(ERR) :integration_time_max: 0
[ 26.617191@5] sensor_print_params@V4L2_drv.c:70 GENERIC(ERR) :integration_time_long_max: 0
[ 26.617194@5] sensor_print_params@V4L2_drv.c:71 GENERIC(ERR) :integration_time_limit: 0
[ 26.617196@5] sensor_print_params@V4L2_drv.c:72 GENERIC(ERR) :day_light_integration_time_max: 0
[ 26.617199@5] sensor_print_params@V4L2_drv.c:73 GENERIC(ERR) :integration_time_apply_delay: 2
[ 26.617201@5] sensor_print_params@V4L2_drv.c:74 GENERIC(ERR) :isp_exposure_channel_delay: 0
[ 26.617204@5] sensor_print_params@V4L2_drv.c:75 GENERIC(ERR) :xoffset: 0
[ 26.617206@5] sensor_print_params@V4L2_drv.c:76 GENERIC(ERR) :yoffset: 0
[ 26.617209@5] sensor_print_params@V4L2_drv.c:77 GENERIC(ERR) :lines_per_second: 0
[ 26.617211@5] sensor_print_params@V4L2_drv.c:78 GENERIC(ERR) :sensor_exp_number: 1
[ 26.617214@5] sensor_print_params@V4L2_drv.c:79 GENERIC(ERR) :modes_num: 6
[ 26.617216@5] sensor_print_params@V4L2_drv.c:80 GENERIC(ERR) :mode: 0
[ 26.617219@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 0
[ 26.617221@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.617223@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1280
[ 26.617226@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 720
[ 26.617229@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 1280
[ 26.617231@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 1
[ 26.617233@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 1
[ 26.617236@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.617238@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.617241@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.617243@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 7680
[ 26.617245@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 1
[ 26.617248@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 2
[ 26.617250@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.617253@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.617255@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.617257@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.617260@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.617262@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 3
[ 26.617265@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.617267@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 3840
[ 26.617269@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 2160
[ 26.617272@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 7680
[ 26.617274@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.617277@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 4
[ 26.617279@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.617281@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 3840
[ 26.617284@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 2160
[ 26.617286@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.617289@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.617291@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 5
[ 26.617293@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 2
[ 26.617296@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.617298@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.617301@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.617303@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.637652@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.637655@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.637785@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.637787@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.637919@5] system_i2c_read:failed to read reg data: rc -6, saddr 0x36
[ 26.637922@5] i2c_io_read_sample@acamera_sbus_i2c.c:98 GENERIC(ERR) :I2C not ok
[ 26.637925@5] sensor_get_id@OV08a10_drv.c:366 GENERIC(ERR) :sensor_get_id: Failed to read sensor id
[ 26.637925@5]
[ 26.637929@5] camera_ioctl@soc_sensor.c:430 GENERIC(ERR) :get isp_seq_num = 0
[ 26.637929@5]
[ 26.637933@5] sensor_print_params@V4L2_drv.c:63 GENERIC(ERR) :SOC SENSOR PARAMETERS
[ 26.637936@5] sensor_print_params@V4L2_drv.c:64 GENERIC(ERR) :pixels_per_line: 0
[ 26.637938@5] sensor_print_params@V4L2_drv.c:65 GENERIC(ERR) :again_log2_max: 2097152
[ 26.637941@5] sensor_print_params@V4L2_drv.c:66 GENERIC(ERR) :dgain_log2_max: 0
[ 26.637943@5] sensor_print_params@V4L2_drv.c:67 GENERIC(ERR) :again_accuracy: 0
[ 26.637946@5] sensor_print_params@V4L2_drv.c:68 GENERIC(ERR) :integration_time_min: 0
[ 26.637948@5] sensor_print_params@V4L2_drv.c:69 GENERIC(ERR) :integration_time_max: 0
[ 26.637951@5] sensor_print_params@V4L2_drv.c:70 GENERIC(ERR) :integration_time_long_max: 0
[ 26.637953@5] sensor_print_params@V4L2_drv.c:71 GENERIC(ERR) :integration_time_limit: 0
[ 26.637956@5] sensor_print_params@V4L2_drv.c:72 GENERIC(ERR) :day_light_integration_time_max: 0
[ 26.637958@5] sensor_print_params@V4L2_drv.c:73 GENERIC(ERR) :integration_time_apply_delay: 2
[ 26.637961@5] sensor_print_params@V4L2_drv.c:74 GENERIC(ERR) :isp_exposure_channel_delay: 0
[ 26.637963@5] sensor_print_params@V4L2_drv.c:75 GENERIC(ERR) :xoffset: 0
[ 26.637965@5] sensor_print_params@V4L2_drv.c:76 GENERIC(ERR) :yoffset: 0
[ 26.637968@5] sensor_print_params@V4L2_drv.c:77 GENERIC(ERR) :lines_per_second: 0
[ 26.637970@5] sensor_print_params@V4L2_drv.c:78 GENERIC(ERR) :sensor_exp_number: 1
[ 26.637973@5] sensor_print_params@V4L2_drv.c:79 GENERIC(ERR) :modes_num: 6
[ 26.637975@5] sensor_print_params@V4L2_drv.c:80 GENERIC(ERR) :mode: 0
[ 26.637978@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 0
[ 26.637980@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.637983@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1280
[ 26.637985@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 720
[ 26.637987@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 1280
[ 26.637990@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 1
[ 26.637992@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 1
[ 26.637995@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.637997@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.637999@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.638002@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 7680
[ 26.638004@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 1
[ 26.638007@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 2
[ 26.638009@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.638011@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.638014@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.638016@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.638019@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.638021@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 3
[ 26.638023@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.638026@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 3840
[ 26.638028@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 2160
[ 26.638031@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 7680
[ 26.638033@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.638035@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 4
[ 26.638038@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 0
[ 26.638040@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 3840
[ 26.638043@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 2160
[ 26.638045@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.638047@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.638050@5] sensor_print_params@V4L2_drv.c:83 GENERIC(ERR) :preset 5
[ 26.638052@5] sensor_print_params@V4L2_drv.c:84 GENERIC(ERR) : mode: 2
[ 26.638055@5] sensor_print_params@V4L2_drv.c:85 GENERIC(ERR) : width: 1920
[ 26.638057@5] sensor_print_params@V4L2_drv.c:86 GENERIC(ERR) : height: 1080
[ 26.638059@5] sensor_print_params@V4L2_drv.c:87 GENERIC(ERR) : fps: 15360
[ 26.638062@5] sensor_print_params@V4L2_drv.c:88 GENERIC(ERR) : exp: 2
[ 26.638068@5] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:104 GENERIC(ERR) :Requested a pointer to the subdev with a name SocCalibrations
[ 26.638071@5] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:111 GENERIC(ERR) :Return subdev pointer 0x2a43400
[ 26.638082@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:39
[ 26.638083@5]
[ 26.638085@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:40
[ 26.638086@5]
[ 26.638088@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:43
[ 26.638088@5]
[ 26.638091@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:44
[ 26.638091@5]
[ 26.638093@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:45
[ 26.638094@5]
[ 26.638098@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:74
[ 26.638099@5]
[ 26.638101@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:75
[ 26.638102@5]
[ 26.638106@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:104
[ 26.638106@5]
[ 26.638109@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:105
[ 26.638109@5]
[ 26.638111@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:107
[ 26.638112@5]
[ 26.638135@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:39
[ 26.638136@5]
[ 26.638139@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:39
[ 26.638139@5]
[ 26.638141@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:40
[ 26.638142@5]
[ 26.638144@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:40
[ 26.638145@5]
[ 26.638148@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:43
[ 26.638148@5]
[ 26.638150@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:43
[ 26.638151@5]
[ 26.638153@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:44
[ 26.638154@5]
[ 26.638156@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:44
[ 26.638157@5]
[ 26.638159@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:45
[ 26.638159@5]
[ 26.638162@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:45
[ 26.638162@5]
[ 26.638175@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:74
[ 26.638176@5]
[ 26.638178@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:74
[ 26.638179@5]
[ 26.638181@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:75
[ 26.638181@5]
[ 26.638184@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:75
[ 26.638184@5]
[ 26.638193@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:104
[ 26.638194@5]
[ 26.638196@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:104
[ 26.638197@5]
[ 26.638199@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:105
[ 26.638199@5]
[ 26.638202@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:105
[ 26.638202@5]
[ 26.638204@5] iq_ioctl@soc_iq.c:97 SUBDEV_IQ(CRIT) :Unitialialized calibration at ctx:0 id:107
[ 26.638205@5]
[ 26.638207@5] iq_ioctl@soc_iq.c:129 SUBDEV_IQ(CRIT) :Uninitialized calibration at ctx:0 id:107
[ 26.638208@5]
[ 26.638216@5] get_calibrations_v4l2@acamera_get_calibrations_v4l2.c:31 GENERIC(CRIT) :Request calibration ctx_id:0 sensor_arg:0x22cde28 from soc_iq device ret 0
[ 26.640087@5] general_set_wdr_mode@general_func.c:453 GENERAL(CRIT) :Setting Linear Binary Sequence
[ 26.640088@5]
[ 26.640301@4] sbuf_mgr_alloc_sbuf@sbuf_func.c:175 SBUF(CRIT) :sbuf: len_needed: 234096, len_alloc: 241663, len_used: 237568, page_size: 4096, buf_alloc: ffffffc0997c0000, buf_used: ffffffc0997c0000.
[ 26.640306@4] sbuf_calibration_init@sbuf_func.c:452 SBUF(ERR) :sbuf_calibration_init.
[ 26.640309@4] get_cur_calibration_total_size@sbuf_func.c:310 SBUF(ERR) :fw_instance: ffffff80022c3960, CALIBRATION_TOTAL_SIZE: 123.
[ 26.640314@4] get_cur_calibration_total_size@sbuf_func.c:325 SBUF(ERR) :Total size for all IQ LUTs is 24852 bytes
[ 26.640317@4] sbuf_mgr_item_count_in_using@sbuf_func.c:427 SBUF(ERR) :sbuf item using total count: 0.
[ 26.640321@4] update_cur_calibration_to_sbuf@sbuf_func.c:362 SBUF(ERR) :sbuf_cali_base: ffffffc0997c009d, p_sbuf_lut_arr: ffffffc0997c009d, p_sbuf_cali_data: ffffffc0997c084d
[ 26.640334@4] sbuf_calibration_init@sbuf_func.c:493 SBUF(CRIT) :sbuf_calibration wdr_mode updated: 65535 -> 0.
[ 26.640343@4] dma_writer_init@dma_writer.c:155 DMA_WRITER(ERR) :DMA_WRITER: Failed to initialize a dma writer type:0 output. 0x0
[ 26.640347@4] dma_writer_init@dma_writer.c:155 DMA_WRITER(ERR) :DMA_WRITER: Failed to initialize a dma writer type:1 output. 0x0
[ 26.640353@4] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:104 GENERIC(ERR) :Requested a pointer to the subdev with a name SocLens
[ 26.640357@4] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:111 GENERIC(ERR) :Return subdev pointer 0x2a95480
[ 26.640360@4] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:104 GENERIC(ERR) :Requested a pointer to the subdev with a name SocLens
[ 26.640363@4] acamera_camera_v4l2_get_subdev_by_name@main_kernel_juno_v4l2.c:111 GENERIC(ERR) :Return subdev pointer 0x2a95480
[ 26.640370@4] lens_init@lens_init.c:139 GENERIC(NOTICE) :Lens VCM driver is NULL
[ 26.640373@4] soc_lens_init@soc_lens.c:62 GENERIC(INFO) :Lens has been initialized for ctx:0
[ 26.640373@4]
[ 26.640376@4] soc_lens_init@soc_lens.c:68 GENERIC(INFO) :Lens has been initialized
[ 26.640380@4] lens_print_params@v4l2_vcm.c:57 GENERIC(ERR) :SOC SENSOR PARAMETERS
[ 26.640383@4] lens_print_params@v4l2_vcm.c:58 GENERIC(ERR) :lens_type: 10
[ 26.640385@4] lens_print_params@v4l2_vcm.c:59 GENERIC(ERR) :min_step: 64
[ 26.640388@4] lens_print_params@v4l2_vcm.c:60 GENERIC(ERR) :next_zoom: 0
[ 26.640390@4] lens_print_params@v4l2_vcm.c:61 GENERIC(ERR) :curr_zoom: 0
[ 26.640393@4] lens_print_params@v4l2_vcm.c:62 GENERIC(ERR) :next_pos: 0
[ 26.641564@4] acamera_init_context_seq@acamera_fw.c:292 GENERIC(ERR) :load isp context sequence[0]
[ 26.641565@4]
[ 26.644600@4] connection_thread@main_firmware.c:102 GENERIC(CRIT) :connection_thread start
[ 26.644668@5] isp_fw_process@main_firmware.c:120 GENERIC(CRIT) :isp_fw_process start
[ 26.644800@4] isp_v4l2_create_instance@isp-v4l2.c:780 GENERIC(CRIT) :V4L2 capture device registered as video0.
[ 26.644815@4] soc_sensor_probe@soc_sensor.c:530 GENERIC(ERR) :register v4l2 sensor device. result 0, sd 0x2ad9d98 sd->dev 0x9b2a0410
[ 26.647660@5] isp_v4l2_stream_try_format@isp-v4l2-stream.c:1326 GENERIC(CRIT) :[Stream#0] format 0x00000000 is not supported, setting default format 0x34424752.
[ 26.647660@5]
[ 26.647754@5] fw_intf_stream_stop@fw-interface.c:331 GENERIC(CRIT) :Stream off 4
[ 26.647755@5]
[ 29.101217@2] meson-remote ff808040.rc: remote_ioctl invalid user space pointer
[ 30.554350@1] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 30.558233@1] meson-mmc: Tuning transfer error: nmatch=0 tuning_err:0xffffffac
[ 30.577263@1] meson-mmc: Tuning transfer error: nmatch=6 tuning_err:0xffffffac
[ 30.874638@0] CONFIG-ERROR) dhd_conf_set_intiovar: txbf setting failed -23
Ubuntu 18.04.5 LTS Khadas ttyS0
Khadas login: khadas
Password:
Last login: Wed Aug 26 09:31:11 PDT 2020 on ttyS0
Welcome to Fenix 0.9.3 Ubuntu 18.04.5 LTS Linux 4.9.232
_ ___ _ __ _____ __ __ _____
| |/ / |__ __ _ __| | __ _ ___ \ \ / /_ _| \/ |___ /
| ' /| '_ \ / _` |/ _` |/ _` / __| \ \ / / | || |\/| | |_ \
| . \| | | | (_| | (_| | (_| \__ \ \ V / | || | | |___) |
|_|\_\_| |_|\__,_|\__,_|\__,_|___/ \_/ |___|_| |_|____/
* Website: https://www.khadas.com
* Documentation: https://docs.khadas.com
* Forum: https://forum.khadas.com
khadas@Khadas:~$
khadas@Khadas:~$
khadas@Khadas:~$
khadas@Khadas:~$ sudo su
[sudo] password for khadas:
root@Khadas:/home/khadas#
root@Khadas:/home/khadas#
root@Khadas:/home/khadas# cat /sys/class/display/mode
1080p60hz
root@Khadas:/home/khadas#
root@Khadas:/home/khadas#
root@Khadas:/home/khadas#
|
提升卡
变色卡
千斤顶
1/10 
京公网安备 11010802033920号
Copyright © 2005-2024 EEWORLD.com.cn, Inc. All rights reserved
