msp430 怎么驱动0.96寸的OLED显示屏（iic）

hysas

msp430 怎么驱动0.96寸的OLED显示屏（iic） [复制链接]

msp430 怎么驱动0.96寸的OLED显示屏（iic），屏幕一直亮不了，谁有完整可以运行的代码啊，求助

ssp

楼主解决了吗？

lisaro

+1模拟i2c可以跑,硬件i2c调不通

lisaro

搞定了！！！！！

•                                  /|\ /|\
• //                   MSP430F5529       4.7k |
• //                 -----------------    |  4.7k
• //            /|\ |             P3.1|---+---|-- I2C Clock (UCB0SCL)
• //             |  |                 |       |
• //             ---|RST          P3.0|-------+-- I2C Data (UCB0SDA)
  记得这两个上拉电阻
•  

lisaro

#include <msp430.h>
#include <stdint.h>
#include <stdbool.h>
#include "OLED_Font.h"
//******************************************************************************
// Example Commands ************************************************************
//******************************************************************************

#define X_WIDTH         128
#define Y_WIDTH         64
#define OLED_CMD  0        //写命令 #define OLED_CMD 0 //写命令
#define OLED_DATA 1        //写数据 #define OLED_DATA 1 //写数据
#define SLAVE_ADDR  0x3C

#define CMD_TYPE_0_SLAVE      0
#define CMD_TYPE_1_SLAVE      1
#define CMD_TYPE_2_SLAVE      2

#define CMD_TYPE_0_MASTER      3
#define CMD_TYPE_1_MASTER      4
#define CMD_TYPE_2_MASTER      5

#define TYPE_0_LENGTH   1
#define TYPE_1_LENGTH   2
#define TYPE_2_LENGTH   6

#define MAX_BUFFER_SIZE     20

uint8_t MasterType2 [TYPE_2_LENGTH] = {'F', '4', '1', '9', '2', 'B'};
uint8_t MasterType1 [28] = {0xae,0x00,0x10,0x40,0x81,0xcf,0xa1,0xc8,0xa6,0xa8,0x3f,0xd3,0x00,0xd5,0x80,0xd9,0xf1,0xda,0x12,0xdb,0x40,0x20,0x02,0x8d,0x14,0xa4,0xa6,0xaf};
uint8_t MasterType0 [1] = {0};

uint8_t SlaveType2 [TYPE_2_LENGTH] = {0};
uint8_t SlaveType1 [TYPE_1_LENGTH] = {0};
uint8_t SlaveType0 [TYPE_0_LENGTH] = {0};
void delay(unsigned int z)
{
  unsigned int x,y;
  for(x=z;x>0;x--)
    for(y=5000;y>0;y--);
}
typedef enum I2C_ModeEnum{
    IDLE_MODE,
    NACK_MODE,
    TX_REG_ADDRESS_MODE,
    RX_REG_ADDRESS_MODE,
    TX_DATA_MODE,
    RX_DATA_MODE,
    SWITCH_TO_RX_MODE,
    SWITHC_TO_TX_MODE,
    TIMEOUT_MODE
} I2C_Mode;

/* Used to track the state of the software state machine*/
I2C_Mode MasterMode = IDLE_MODE;

/* The Register Address/Command to use*/
uint8_t TransmitRegAddr = 0;

/* ReceiveBuffer: Buffer used to receive data in the ISR
 * RXByteCtr: Number of bytes left to receive
 * ReceiveIndex: The index of the next byte to be received in ReceiveBuffer
 * TransmitBuffer: Buffer used to transmit data in the ISR
 * TXByteCtr: Number of bytes left to transfer
 * TransmitIndex: The index of the next byte to be transmitted in TransmitBuffer
 * */
uint8_t ReceiveBuffer[MAX_BUFFER_SIZE] = {0};
uint8_t RXByteCtr = 0;
uint8_t ReceiveIndex = 0;
uint8_t TransmitBuffer[MAX_BUFFER_SIZE] = {0};
uint8_t TXByteCtr = 0;
uint8_t TransmitIndex = 0;

I2C_Mode I2C_Master_WriteReg(uint8_t dev_addr, uint8_t reg_addr, uint8_t *reg_data, uint8_t count);

I2C_Mode I2C_Master_ReadReg(uint8_t dev_addr, uint8_t reg_addr, uint8_t count);
void CopyArray(uint8_t *source, uint8_t *dest, uint8_t count);

I2C_Mode I2C_Master_ReadReg(uint8_t dev_addr, uint8_t reg_addr, uint8_t count)
{
    /* Initialize state machine */
    MasterMode = TX_REG_ADDRESS_MODE;
    TransmitRegAddr = reg_addr;
    RXByteCtr = count;
    TXByteCtr = 0;
    ReceiveIndex = 0;
    TransmitIndex = 0;

    /* Initialize slave address and interrupts */
    UCB0I2CSA = dev_addr;
    IFG2 &= ~(UCB0TXIFG + UCB0RXIFG);       // Clear any pending interrupts
    IE2 &= ~UCB0RXIE;                       // Disable RX interrupt
    IE2 |= UCB0TXIE;                        // Enable TX interrupt

    UCB0CTL1 |= UCTR + UCTXSTT;             // I2C TX, start condition
    __bis_SR_register(CPUOFF + GIE);              // Enter LPM0 w/ interrupts

    return MasterMode;

}

I2C_Mode I2C_Master_WriteReg(uint8_t dev_addr, uint8_t reg_addr, uint8_t *reg_data, uint8_t count)
{
    /* Initialize state machine */
    MasterMode = TX_REG_ADDRESS_MODE;
    TransmitRegAddr = reg_addr;

    //Copy register data to TransmitBuffer
    CopyArray(reg_data, TransmitBuffer, count);

    TXByteCtr = count;
    RXByteCtr = 0;
    ReceiveIndex = 0;
    TransmitIndex = 0;

    /* Initialize slave address and interrupts */
    UCB0I2CSA = dev_addr;
    IFG2 &= ~(UCB0TXIFG + UCB0RXIFG);       // Clear any pending interrupts
    IE2 &= ~UCB0RXIE;                       // Disable RX interrupt
    IE2 |= UCB0TXIE;                        // Enable TX interrupt

    UCB0CTL1 |= UCTR + UCTXSTT;             // I2C TX, start condition
    __bis_SR_register(CPUOFF + GIE);              // Enter LPM0 w/ interrupts

    return MasterMode;
}
void CopyArray(uint8_t *source, uint8_t *dest, uint8_t count)
{
    uint8_t copyIndex = 0;
    for (copyIndex = 0; copyIndex < count; copyIndex++)
    {
        dest[copyIndex] = source[copyIndex];
    }
}

void initClockTo16MHz()
{
    if (CALBC1_16MHZ==0xFF)                  // If calibration constant erased
    {
        while(1);                               // do not load, trap CPU!!
    }
    DCOCTL = 0;                               // Select lowest DCOx and MODx settings
    BCSCTL1 = CALBC1_16MHZ;                    // Set DCO
    DCOCTL = CALDCO_16MHZ;
}

void initGPIO()
{
    P1DIR |= BIT0 + BIT1 + BIT2 + BIT3 + BIT4;
    P1OUT &= ~(BIT0 + BIT1 + BIT2 + BIT3 + BIT4);

    P1SEL |= BIT6 + BIT7;                     // Assign I2C pins to USCI_B0
    P1SEL2|= BIT6 + BIT7;                     // Assign I2C pins to USCI_B0
}

void initI2C()
{
    UCB0CTL1 |= UCSWRST;                      // Enable SW reset
    UCB0CTL0 = UCMST + UCMODE_3 + UCSYNC;     // I2C Master, synchronous mode
    UCB0CTL1 = UCSSEL_2 + UCSWRST;            // Use SMCLK, keep SW reset
    UCB0BR0 = 160;                            // fSCL = SMCLK/160 = ~100kHz
    UCB0BR1 = 0;
    UCB0I2CSA = SLAVE_ADDR;                   // Slave Address
    UCB0CTL1 &= ~UCSWRST;                     // Clear SW reset, resume operation
    UCB0I2CIE |= UCNACKIE;
}

void OLED_WriteCommand(unsigned char IIC_Command)
{
        MasterType0[0]=IIC_Command;
      I2C_Master_WriteReg(SLAVE_ADDR, 0x00,MasterType0, 1);
}
void OLED_WriteData(unsigned char IIC_Data)
{
        MasterType0[0]=IIC_Data;
      I2C_Master_WriteReg(SLAVE_ADDR, 0x40,MasterType0, 1);
}
//******************************************************************************
// Main ************************************************************************
// Send and receive three messages containing the example commands *************
//******************************************************************************
void OLED_Fill(unsigned char bmp_dat)
{
        unsigned char y,x;
        for(y=0;y<8;y++)
        {
            OLED_WriteCommand(0xb0+y);
            OLED_WriteCommand(0x01);
            OLED_WriteCommand(0x10);
                for(x=0;x<128;x++)
            OLED_WriteData(bmp_dat);
        }
}
void OLED_SetCursor(uint8_t Y, uint8_t X)
{
    OLED_WriteCommand(0xB0 | Y);                    //设置Y位置
    OLED_WriteCommand(0x10 | ((X & 0xF0) >> 4));    //设置X位置高4位
    OLED_WriteCommand(0x00 | (X & 0x0F));           //设置X位置低4位
}
void OLED_Init(void)
{
        unsigned char i=0;
        for(;i<28;i++)
        {
          MasterType0[0]=MasterType1;
          I2C_Master_WriteReg(SLAVE_ADDR, 0x00,MasterType0, 1);
        }
        OLED_Fill(0x00); //初始清屏
        OLED_SetCursor(0,0);
}
void OLED_ShowChar(uint8_t Line, uint8_t Column, char Char)
{
    uint8_t i;
    OLED_SetCursor((Line - 1) * 2, (Column - 1) * 8);       //设置光标位置在上半部分
    for (i = 0; i < 8; i++)
    {
        OLED_WriteData(OLED_F8x16[Char - ' ']);          //显示上半部分内容
    }
    OLED_SetCursor((Line - 1) * 2 + 1, (Column - 1) * 8);   //设置光标位置在下半部分
    for (i = 0; i < 8; i++)
    {
        OLED_WriteData(OLED_F8x16[Char - ' '][i + 8]);      //显示下半部分内容
    }
}

/**
  * @brief  OLED显示字符串
  * @param  Line 起始行位置，范围：1~4
  * @param  Column 起始列位置，范围：1~16
  * @param  String 要显示的字符串，范围：ASCII可见字符
  * @retval 无
  */
void OLED_ShowString(uint8_t Line, uint8_t Column, char *String)
{
    uint8_t i;
    for (i = 0; String != '\0'; i++)
    {
        OLED_ShowChar(Line, Column + i, String);
    }
}

/**
  * @brief  OLED次方函数
  * @retval 返回值等于X的Y次方
  */
uint32_t OLED_Pow(uint32_t X, uint32_t Y)
{
    uint32_t Result = 1;
    while (Y--)
    {
        Result *= X;
    }
    return Result;
}

/**
  * @brief  OLED显示数字（十进制，正数）
  * @param  Line 起始行位置，范围：1~4
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~4294967295
  * @param  Length 要显示数字的长度，范围：1~10
  * @retval 无
  */
void OLED_ShowNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{
    uint8_t i;
    for (i = 0; i < Length; i++)
    {
        OLED_ShowChar(Line, Column + i, Number / OLED_Pow(10, Length - i - 1) % 10 + '0');
    }
}

/**
  * @brief  OLED显示数字（十进制，带符号数）
  * @param  Line 起始行位置，范围：1~4
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：-2147483648~2147483647
  * @param  Length 要显示数字的长度，范围：1~10
  * @retval 无
  */
void OLED_ShowSignedNum(uint8_t Line, uint8_t Column, int32_t Number, uint8_t Length)
{
    uint8_t i;
    uint32_t Number1;
    if (Number >= 0)
    {
        OLED_ShowChar(Line, Column, '+');
        Number1 = Number;
    }
    else
    {
        OLED_ShowChar(Line, Column, '-');
        Number1 = -Number;
    }
    for (i = 0; i < Length; i++)
    {
        OLED_ShowChar(Line, Column + i + 1, Number1 / OLED_Pow(10, Length - i - 1) % 10 + '0');
    }
}

/**
  * @brief  OLED显示数字（十六进制，正数）
  * @param  Line 起始行位置，范围：1~4
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~0xFFFFFFFF
  * @param  Length 要显示数字的长度，范围：1~8
  * @retval 无
  */
void OLED_ShowHexNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{
    uint8_t i, SingleNumber;
    for (i = 0; i < Length; i++)
    {
        SingleNumber = Number / OLED_Pow(16, Length - i - 1) % 16;
        if (SingleNumber < 10)
        {
            OLED_ShowChar(Line, Column + i, SingleNumber + '0');
        }
        else
        {
            OLED_ShowChar(Line, Column + i, SingleNumber - 10 + 'A');
        }
    }
}

/**
  * @brief  OLED显示数字（二进制，正数）
  * @param  Line 起始行位置，范围：1~4
  * @param  Column 起始列位置，范围：1~16
  * @param  Number 要显示的数字，范围：0~1111 1111 1111 1111
  * @param  Length 要显示数字的长度，范围：1~16
  * @retval 无
  */
void OLED_ShowBinNum(uint8_t Line, uint8_t Column, uint32_t Number, uint8_t Length)
{
    uint8_t i;
    for (i = 0; i < Length; i++)
    {
        OLED_ShowChar(Line, Column + i, Number / OLED_Pow(2, Length - i - 1) % 2 + '0');
    }
}
//******************************************************************************
// Main ************************************************************************
// Send and receive three messages containing the example commands *************
//******************************************************************************

int main(void) {

    WDTCTL = WDTPW | WDTHOLD;                 // Stop watchdog timer

    initClockTo16MHz();
    initGPIO();
    initI2C();
    delay(500);
    OLED_Init();
    OLED_ShowNum(1,1,500,3);
    __bis_SR_register(LPM0_bits + GIE);
    return 0;
}

//******************************************************************************
// I2C Interrupt For Received and Transmitted Data******************************
//******************************************************************************

#if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__)
#pragma vector = USCIAB0TX_VECTOR
__interrupt void USCIAB0TX_ISR(void)
#elif defined(__GNUC__)
void __attribute__ ((interrupt(USCIAB0TX_VECTOR))) USCIAB0TX_ISR (void)
#else
#error Compiler not supported!
#endif
{
  if (IFG2 & UCB0RXIFG)                 // Receive Data Interrupt
  {
      //Must read from UCB0RXBUF
      uint8_t rx_val = UCB0RXBUF;

      if (RXByteCtr)
      {
          ReceiveBuffer[ReceiveIndex++] = rx_val;
          RXByteCtr--;
      }

      if (RXByteCtr == 1)
      {
          UCB0CTL1 |= UCTXSTP;
      }
      else if (RXByteCtr == 0)
      {
          IE2 &= ~UCB0RXIE;
          MasterMode = IDLE_MODE;
          __bic_SR_register_on_exit(CPUOFF);      // Exit LPM0
      }
  }
  else if (IFG2 & UCB0TXIFG)            // Transmit Data Interrupt
  {
      switch (MasterMode)
      {
          case TX_REG_ADDRESS_MODE:
              UCB0TXBUF = TransmitRegAddr;
              if (RXByteCtr)
                  MasterMode = SWITCH_TO_RX_MODE;   // Need to start receiving now
              else
                  MasterMode = TX_DATA_MODE;        // Continue to transmision with the data in Transmit Buffer
              break;

          case SWITCH_TO_RX_MODE:
              IE2 |= UCB0RXIE;              // Enable RX interrupt
              IE2 &= ~UCB0TXIE;             // Disable TX interrupt
              UCB0CTL1 &= ~UCTR;            // Switch to receiver
              MasterMode = RX_DATA_MODE;    // State state is to receive data
              UCB0CTL1 |= UCTXSTT;          // Send repeated start
              if (RXByteCtr == 1)
              {
                  //Must send stop since this is the N-1 byte
                  while((UCB0CTL1 & UCTXSTT));
                  UCB0CTL1 |= UCTXSTP;      // Send stop condition
              }
              break;

          case TX_DATA_MODE:
              if (TXByteCtr)
              {
                  UCB0TXBUF = TransmitBuffer[TransmitIndex++];
                  TXByteCtr--;
              }
              else
              {
                  //Done with transmission
                  UCB0CTL1 |= UCTXSTP;     // Send stop condition
                  MasterMode = IDLE_MODE;
                  IE2 &= ~UCB0TXIE;                       // disable TX interrupt
                  __bic_SR_register_on_exit(CPUOFF);      // Exit LPM0
              }
              break;

          default:
              __no_operation();
              break;
      }
  }
}

//******************************************************************************
// I2C Interrupt For Start, Restart, Nack, Stop ********************************
//******************************************************************************

#if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__)
#pragma vector = USCIAB0RX_VECTOR
__interrupt void USCIAB0RX_ISR(void)
#elif defined(__GNUC__)
void __attribute__ ((interrupt(USCIAB0RX_VECTOR))) USCIAB0RX_ISR (void)
#else
#error Compiler not supported!
#endif
{
    if (UCB0STAT & UCNACKIFG)
    {
        UCB0STAT &= ~UCNACKIFG;             // Clear NACK Flags
    }
    if (UCB0STAT & UCSTPIFG)                        //Stop or NACK Interrupt
    {
        UCB0STAT &=
            ~(UCSTTIFG + UCSTPIFG + UCNACKIFG);     //Clear START/STOP/NACK Flags
    }
    if (UCB0STAT & UCSTTIFG)
    {
        UCB0STAT &= ~(UCSTTIFG);                    //Clear START Flags
    }
}
 

 

lisaro

#ifndef __OLED_FONT_H
#define __OLED_FONT_H
#include "stdint.h"
/*OLED字模库，宽8像素，高16像素*/
const uint8_t OLED_F8x16[][16]=
{
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//  0

    0x00,0x00,0x00,0xF8,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x33,0x30,0x00,0x00,0x00,//! 1

    0x00,0x10,0x0C,0x06,0x10,0x0C,0x06,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//" 2

    0x40,0xC0,0x78,0x40,0xC0,0x78,0x40,0x00,
    0x04,0x3F,0x04,0x04,0x3F,0x04,0x04,0x00,//# 3

    0x00,0x70,0x88,0xFC,0x08,0x30,0x00,0x00,
    0x00,0x18,0x20,0xFF,0x21,0x1E,0x00,0x00,//$ 4

    0xF0,0x08,0xF0,0x00,0xE0,0x18,0x00,0x00,
    0x00,0x21,0x1C,0x03,0x1E,0x21,0x1E,0x00,//% 5

    0x00,0xF0,0x08,0x88,0x70,0x00,0x00,0x00,
    0x1E,0x21,0x23,0x24,0x19,0x27,0x21,0x10,//& 6

    0x10,0x16,0x0E,0x00,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//' 7

    0x00,0x00,0x00,0xE0,0x18,0x04,0x02,0x00,
    0x00,0x00,0x00,0x07,0x18,0x20,0x40,0x00,//( 8

    0x00,0x02,0x04,0x18,0xE0,0x00,0x00,0x00,
    0x00,0x40,0x20,0x18,0x07,0x00,0x00,0x00,//) 9

    0x40,0x40,0x80,0xF0,0x80,0x40,0x40,0x00,
    0x02,0x02,0x01,0x0F,0x01,0x02,0x02,0x00,//* 10

    0x00,0x00,0x00,0xF0,0x00,0x00,0x00,0x00,
    0x01,0x01,0x01,0x1F,0x01,0x01,0x01,0x00,//+ 11

    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x80,0xB0,0x70,0x00,0x00,0x00,0x00,0x00,//, 12

    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x01,0x01,0x01,0x01,0x01,0x01,0x01,//- 13

    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x00,0x30,0x30,0x00,0x00,0x00,0x00,0x00,//. 14

    0x00,0x00,0x00,0x00,0x80,0x60,0x18,0x04,
    0x00,0x60,0x18,0x06,0x01,0x00,0x00,0x00,/// 15

    0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,
    0x00,0x0F,0x10,0x20,0x20,0x10,0x0F,0x00,//0 16

    0x00,0x10,0x10,0xF8,0x00,0x00,0x00,0x00,
    0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//1 17

    0x00,0x70,0x08,0x08,0x08,0x88,0x70,0x00,
    0x00,0x30,0x28,0x24,0x22,0x21,0x30,0x00,//2 18

    0x00,0x30,0x08,0x88,0x88,0x48,0x30,0x00,
    0x00,0x18,0x20,0x20,0x20,0x11,0x0E,0x00,//3 19

    0x00,0x00,0xC0,0x20,0x10,0xF8,0x00,0x00,
    0x00,0x07,0x04,0x24,0x24,0x3F,0x24,0x00,//4 20

    0x00,0xF8,0x08,0x88,0x88,0x08,0x08,0x00,
    0x00,0x19,0x21,0x20,0x20,0x11,0x0E,0x00,//5 21

    0x00,0xE0,0x10,0x88,0x88,0x18,0x00,0x00,
    0x00,0x0F,0x11,0x20,0x20,0x11,0x0E,0x00,//6 22

    0x00,0x38,0x08,0x08,0xC8,0x38,0x08,0x00,
    0x00,0x00,0x00,0x3F,0x00,0x00,0x00,0x00,//7 23

    0x00,0x70,0x88,0x08,0x08,0x88,0x70,0x00,
    0x00,0x1C,0x22,0x21,0x21,0x22,0x1C,0x00,//8 24

    0x00,0xE0,0x10,0x08,0x08,0x10,0xE0,0x00,
    0x00,0x00,0x31,0x22,0x22,0x11,0x0F,0x00,//9 25

    0x00,0x00,0x00,0xC0,0xC0,0x00,0x00,0x00,
    0x00,0x00,0x00,0x30,0x30,0x00,0x00,0x00,//: 26

    0x00,0x00,0x00,0x80,0x00,0x00,0x00,0x00,
    0x00,0x00,0x80,0x60,0x00,0x00,0x00,0x00,//; 27

    0x00,0x00,0x80,0x40,0x20,0x10,0x08,0x00,
    0x00,0x01,0x02,0x04,0x08,0x10,0x20,0x00,//< 28

    0x40,0x40,0x40,0x40,0x40,0x40,0x40,0x00,
    0x04,0x04,0x04,0x04,0x04,0x04,0x04,0x00,//= 29

    0x00,0x08,0x10,0x20,0x40,0x80,0x00,0x00,
    0x00,0x20,0x10,0x08,0x04,0x02,0x01,0x00,//> 30

    0x00,0x70,0x48,0x08,0x08,0x08,0xF0,0x00,
    0x00,0x00,0x00,0x30,0x36,0x01,0x00,0x00,//? 31

    0xC0,0x30,0xC8,0x28,0xE8,0x10,0xE0,0x00,
    0x07,0x18,0x27,0x24,0x23,0x14,0x0B,0x00,//@ 32

    0x00,0x00,0xC0,0x38,0xE0,0x00,0x00,0x00,
    0x20,0x3C,0x23,0x02,0x02,0x27,0x38,0x20,//A 33

    0x08,0xF8,0x88,0x88,0x88,0x70,0x00,0x00,
    0x20,0x3F,0x20,0x20,0x20,0x11,0x0E,0x00,//B 34

    0xC0,0x30,0x08,0x08,0x08,0x08,0x38,0x00,
    0x07,0x18,0x20,0x20,0x20,0x10,0x08,0x00,//C 35

    0x08,0xF8,0x08,0x08,0x08,0x10,0xE0,0x00,
    0x20,0x3F,0x20,0x20,0x20,0x10,0x0F,0x00,//D 36

    0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,
    0x20,0x3F,0x20,0x20,0x23,0x20,0x18,0x00,//E 37

    0x08,0xF8,0x88,0x88,0xE8,0x08,0x10,0x00,
    0x20,0x3F,0x20,0x00,0x03,0x00,0x00,0x00,//F 38

    0xC0,0x30,0x08,0x08,0x08,0x38,0x00,0x00,
    0x07,0x18,0x20,0x20,0x22,0x1E,0x02,0x00,//G 39

    0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,
    0x20,0x3F,0x21,0x01,0x01,0x21,0x3F,0x20,//H 40

    0x00,0x08,0x08,0xF8,0x08,0x08,0x00,0x00,
    0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//I 41

    0x00,0x00,0x08,0x08,0xF8,0x08,0x08,0x00,
    0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,0x00,//J 42

    0x08,0xF8,0x88,0xC0,0x28,0x18,0x08,0x00,
    0x20,0x3F,0x20,0x01,0x26,0x38,0x20,0x00,//K 43

    0x08,0xF8,0x08,0x00,0x00,0x00,0x00,0x00,
    0x20,0x3F,0x20,0x20,0x20,0x20,0x30,0x00,//L 44

    0x08,0xF8,0xF8,0x00,0xF8,0xF8,0x08,0x00,
    0x20,0x3F,0x00,0x3F,0x00,0x3F,0x20,0x00,//M 45

    0x08,0xF8,0x30,0xC0,0x00,0x08,0xF8,0x08,
    0x20,0x3F,0x20,0x00,0x07,0x18,0x3F,0x00,//N 46

    0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,
    0x0F,0x10,0x20,0x20,0x20,0x10,0x0F,0x00,//O 47

    0x08,0xF8,0x08,0x08,0x08,0x08,0xF0,0x00,
    0x20,0x3F,0x21,0x01,0x01,0x01,0x00,0x00,//P 48

    0xE0,0x10,0x08,0x08,0x08,0x10,0xE0,0x00,
    0x0F,0x18,0x24,0x24,0x38,0x50,0x4F,0x00,//Q 49

    0x08,0xF8,0x88,0x88,0x88,0x88,0x70,0x00,
    0x20,0x3F,0x20,0x00,0x03,0x0C,0x30,0x20,//R 50

    0x00,0x70,0x88,0x08,0x08,0x08,0x38,0x00,
    0x00,0x38,0x20,0x21,0x21,0x22,0x1C,0x00,//S 51

    0x18,0x08,0x08,0xF8,0x08,0x08,0x18,0x00,
    0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//T 52

    0x08,0xF8,0x08,0x00,0x00,0x08,0xF8,0x08,
    0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//U 53

    0x08,0x78,0x88,0x00,0x00,0xC8,0x38,0x08,
    0x00,0x00,0x07,0x38,0x0E,0x01,0x00,0x00,//V 54

    0xF8,0x08,0x00,0xF8,0x00,0x08,0xF8,0x00,
    0x03,0x3C,0x07,0x00,0x07,0x3C,0x03,0x00,//W 55

    0x08,0x18,0x68,0x80,0x80,0x68,0x18,0x08,
    0x20,0x30,0x2C,0x03,0x03,0x2C,0x30,0x20,//X 56

    0x08,0x38,0xC8,0x00,0xC8,0x38,0x08,0x00,
    0x00,0x00,0x20,0x3F,0x20,0x00,0x00,0x00,//Y 57

    0x10,0x08,0x08,0x08,0xC8,0x38,0x08,0x00,
    0x20,0x38,0x26,0x21,0x20,0x20,0x18,0x00,//Z 58

    0x00,0x00,0x00,0xFE,0x02,0x02,0x02,0x00,
    0x00,0x00,0x00,0x7F,0x40,0x40,0x40,0x00,//[ 59

    0x00,0x0C,0x30,0xC0,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x01,0x06,0x38,0xC0,0x00,//\ 60

    0x00,0x02,0x02,0x02,0xFE,0x00,0x00,0x00,
    0x00,0x40,0x40,0x40,0x7F,0x00,0x00,0x00,//] 61

    0x00,0x00,0x04,0x02,0x02,0x02,0x04,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//^ 62

    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,
    0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x80,//_ 63

    0x00,0x02,0x02,0x04,0x00,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//` 64

    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,
    0x00,0x19,0x24,0x22,0x22,0x22,0x3F,0x20,//a 65

    0x08,0xF8,0x00,0x80,0x80,0x00,0x00,0x00,
    0x00,0x3F,0x11,0x20,0x20,0x11,0x0E,0x00,//b 66

    0x00,0x00,0x00,0x80,0x80,0x80,0x00,0x00,
    0x00,0x0E,0x11,0x20,0x20,0x20,0x11,0x00,//c 67

    0x00,0x00,0x00,0x80,0x80,0x88,0xF8,0x00,
    0x00,0x0E,0x11,0x20,0x20,0x10,0x3F,0x20,//d 68

    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,
    0x00,0x1F,0x22,0x22,0x22,0x22,0x13,0x00,//e 69

    0x00,0x80,0x80,0xF0,0x88,0x88,0x88,0x18,
    0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//f 70

    0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,
    0x00,0x6B,0x94,0x94,0x94,0x93,0x60,0x00,//g 71

    0x08,0xF8,0x00,0x80,0x80,0x80,0x00,0x00,
    0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//h 72

    0x00,0x80,0x98,0x98,0x00,0x00,0x00,0x00,
    0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//i 73

    0x00,0x00,0x00,0x80,0x98,0x98,0x00,0x00,
    0x00,0xC0,0x80,0x80,0x80,0x7F,0x00,0x00,//j 74

    0x08,0xF8,0x00,0x00,0x80,0x80,0x80,0x00,
    0x20,0x3F,0x24,0x02,0x2D,0x30,0x20,0x00,//k 75

    0x00,0x08,0x08,0xF8,0x00,0x00,0x00,0x00,
    0x00,0x20,0x20,0x3F,0x20,0x20,0x00,0x00,//l 76

    0x80,0x80,0x80,0x80,0x80,0x80,0x80,0x00,
    0x20,0x3F,0x20,0x00,0x3F,0x20,0x00,0x3F,//m 77

    0x80,0x80,0x00,0x80,0x80,0x80,0x00,0x00,
    0x20,0x3F,0x21,0x00,0x00,0x20,0x3F,0x20,//n 78

    0x00,0x00,0x80,0x80,0x80,0x80,0x00,0x00,
    0x00,0x1F,0x20,0x20,0x20,0x20,0x1F,0x00,//o 79

    0x80,0x80,0x00,0x80,0x80,0x00,0x00,0x00,
    0x80,0xFF,0xA1,0x20,0x20,0x11,0x0E,0x00,//p 80

    0x00,0x00,0x00,0x80,0x80,0x80,0x80,0x00,
    0x00,0x0E,0x11,0x20,0x20,0xA0,0xFF,0x80,//q 81

    0x80,0x80,0x80,0x00,0x80,0x80,0x80,0x00,
    0x20,0x20,0x3F,0x21,0x20,0x00,0x01,0x00,//r 82

    0x00,0x00,0x80,0x80,0x80,0x80,0x80,0x00,
    0x00,0x33,0x24,0x24,0x24,0x24,0x19,0x00,//s 83

    0x00,0x80,0x80,0xE0,0x80,0x80,0x00,0x00,
    0x00,0x00,0x00,0x1F,0x20,0x20,0x00,0x00,//t 84

    0x80,0x80,0x00,0x00,0x00,0x80,0x80,0x00,
    0x00,0x1F,0x20,0x20,0x20,0x10,0x3F,0x20,//u 85

    0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,
    0x00,0x01,0x0E,0x30,0x08,0x06,0x01,0x00,//v 86

    0x80,0x80,0x00,0x80,0x00,0x80,0x80,0x80,
    0x0F,0x30,0x0C,0x03,0x0C,0x30,0x0F,0x00,//w 87

    0x00,0x80,0x80,0x00,0x80,0x80,0x80,0x00,
    0x00,0x20,0x31,0x2E,0x0E,0x31,0x20,0x00,//x 88

    0x80,0x80,0x80,0x00,0x00,0x80,0x80,0x80,
    0x80,0x81,0x8E,0x70,0x18,0x06,0x01,0x00,//y 89

    0x00,0x80,0x80,0x80,0x80,0x80,0x80,0x00,
    0x00,0x21,0x30,0x2C,0x22,0x21,0x30,0x00,//z 90

    0x00,0x00,0x00,0x00,0x80,0x7C,0x02,0x02,
    0x00,0x00,0x00,0x00,0x00,0x3F,0x40,0x40,//{ 91

    0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,
    0x00,0x00,0x00,0x00,0xFF,0x00,0x00,0x00,//| 92

    0x00,0x02,0x02,0x7C,0x80,0x00,0x00,0x00,
    0x00,0x40,0x40,0x3F,0x00,0x00,0x00,0x00,//} 93

    0x00,0x06,0x01,0x01,0x02,0x02,0x04,0x04,
    0x00,0x00,0x00,0x00,0x00,0x00,0x00,0x00,//~ 94
};
char Hzk[][32]={

{0x00,0x00,0xF0,0x10,0x10,0x10,0x10,0xFF,0x10,0x10,0x10,0x10,0xF0,0x00,0x00,0x00},
{0x00,0x00,0x0F,0x04,0x04,0x04,0x04,0xFF,0x04,0x04,0x04,0x04,0x0F,0x00,0x00,0x00},/*"中",0*/

};

#endif