MSP430串口在接收到电脑发送数据

fish001

MSP430串口在接收到电脑发送数据 [复制链接]

#include "driverlib.h"
//#include "Board.h"

uint16_t i;
uint8_t RXData = 0, TXData = 0;
uint8_t check = 0;

void main(void)
{
    //Stop Watchdog Timer
    WDT_A_hold(WDT_A_BASE);

    //Set ACLK = REFOCLK with clock divider of 1
    CS_initClockSignal(CS_ACLK,CS_REFOCLK_SELECT,CS_CLOCK_DIVIDER_1);
    //Set SMCLK = DCO with frequency divider of 1
    CS_initClockSignal(CS_SMCLK,CS_DCOCLKDIV_SELECT,CS_CLOCK_DIVIDER_1);
    //Set MCLK = DCO with frequency divider of 1
    CS_initClockSignal(CS_MCLK,CS_DCOCLKDIV_SELECT,CS_CLOCK_DIVIDER_1);


    //Configure UART pins
    GPIO_setAsPeripheralModuleFunctionInputPin(
        GPIO_PORT_P1,
        GPIO_PIN6 + GPIO_PIN7,
        GPIO_PRIMARY_MODULE_FUNCTION
        );

    /*
     * Disable the GPIO power-on default high-impedance mode to activate
     * previously configured port settings
     */
    PMM_unlockLPM5();

    //Configure UART
    //SMCLK = 1MHz, Baudrate =9600
    //UCBRx =6, UCBRFx = 8, UCBRSx = 17, UCOS16 = 1
    EUSCI_A_UART_initParam param = {0};
    param.selectClockSource = EUSCI_A_UART_CLOCKSOURCE_SMCLK;
    param.clockPrescalar = 6;
    param.firstModReg = 8;
    param.secondModReg = 17;
    param.parity = EUSCI_A_UART_NO_PARITY;
    param.msborLsbFirst = EUSCI_A_UART_LSB_FIRST;
    param.numberofStopBits = EUSCI_A_UART_ONE_STOP_BIT;
    param.uartMode = EUSCI_A_UART_MODE;
    param.overSampling = EUSCI_A_UART_OVERSAMPLING_BAUDRATE_GENERATION;

    if (STATUS_FAIL == EUSCI_A_UART_init(EUSCI_A0_BASE, &param)) {
        return;
    }

    EUSCI_A_UART_enable(EUSCI_A0_BASE);

    EUSCI_A_UART_clearInterrupt(EUSCI_A0_BASE,
        EUSCI_A_UART_RECEIVE_INTERRUPT);

    // Enable USCI_A0 RX interrupt
    EUSCI_A_UART_enableInterrupt(EUSCI_A0_BASE,
        EUSCI_A_UART_RECEIVE_INTERRUPT);

    // Enable global interrupts
    __enable_interrupt();

    EUSCI_A_UART_transmitData(EUSCI_A0_BASE, TXData);

    while (1)
    {
//         Increment TX data
        TXData = TXData+1;
//         Load data onto buffer
        EUSCI_A_UART_transmitData(EUSCI_A0_BASE, TXData);
        while(check != 1);
        check = 0;
    }
}
//******************************************************************************
//
//This is the USCI_A0 interrupt vector service routine.
//
//******************************************************************************
#if defined(__TI_COMPILER_VERSION__) || defined(__IAR_SYSTEMS_ICC__)
#pragma vector=USCI_A0_VECTOR
__interrupt
#elif defined(__GNUC__)
__attribute__((interrupt(USCI_A0_VECTOR)))
#endif
void EUSCI_A0_ISR(void)
{
    switch(__even_in_range(UCA0IV,USCI_UART_UCTXCPTIFG))
    {
        case USCI_NONE: break;
        case USCI_UART_UCRXIFG:
      RXData = EUSCI_A_UART_receiveData(EUSCI_A0_BASE);


            EUSCI_A_UART_transmitData(EUSCI_A0_BASE, RXData);
            // Check value
            if(!(RXData == TXData))
            {
                while(1);
            }
            check =1;
         //   UCA0IFG = 0;
            break;
       case USCI_UART_UCTXIFG: break;
       case USCI_UART_UCSTTIFG: break;
       case USCI_UART_UCTXCPTIFG: break;
    }
}