nengzhi的个人空间动态-电子工程世界

nengzhi

动态发布点评好友关于

2024-06-04
发表了主题帖： ST NUCLEO-U083RC 评测 ——智能坐垫功耗测试

书接上回，对基于开发板构建的智能坐垫原型进行了实际的功耗测试。测试结果如下图所示，使用合宙的IOT Power CC功耗计，固件版本是1.3.2。整个测试工况按照预计的实际中的功耗最大模式设计。开发板上有颗电源指示LED没拆除，所以功耗肯定要比实际高。按照测试好的功耗计算，使用480mAh的锂电池，可以在测试工况下连续工作12小时。按照这个测试结果估计，在经过PCB优化和实际工况优化后，实际的工作时长有望达到72小时。是一款在本产品中值得继续优化下去的MCU。
2024-05-31
发表了主题帖： ST NUCLEO-U083RC 评测——智能坐垫移植笔记

本帖最后由 nengzhi 于 2024-6-3 17:38 编辑有幸被选中参加STM32U0开发板的评测活动。原打算把一个智能坐垫的项目移植过来试一试功耗能不能降到更低。但无奈手头杂事太多，一再耽搁，今天小编通知我活动截至时间到了，也没来得及完成最终的实际功耗测试，索性功能移植的差不多了，就把移植过程中的一些记录拿来分享一下。先来个开箱视频把，早就录好了。 https://b23.tv/12Sv54u 然后就是移植过程中的一些记录。我是第一次接触STM32 的开发，原本一直在搞Arduino下的ESP32开发，所以这次是从头开始学习STM32开发的，所以记录一下移植过程。本次移植涉及到了RTC，串口、Flash以及低功耗等部分。先说一下我的开发环境，我用的STM32Cube IDE开发。参考B站教程。全网最完整最干练的CubeMX、CubeIDE STM32开发教程拥抱高效Cube开发方式【3.1】—Kevin带你读《STM32Cube高效开发教程基础篇》_哔哩哔哩_bilibili 开发板特性先来介绍下开发板的特点。开发板自带ST-Link，这个ST-Link是自带虚拟串口的和STM32的LPUART1连在一起。 D1和D0跳线默认时断开的。没有外接高速晶振，只有一个低速晶振。拥有256K flash。如下代码是把printf重定向到LUART1 /* USER CODE BEGIN Includes */ #include<stdio.h> #include<string.h> /* USER CODE END Includes */ /* Private variables ---------------------------------------------------------*/ UART_HandleTypeDef hlpuart1; /* USER CODE BEGIN PV */ #ifdef __GNUC__ #define PUTCHAR_PROTOTYPE int __io_putchar(int ch) #else #define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f) #endif PUTCHAR_PROTOTYPE { //同样USART2改为你的串口 HAL_UART_Transmit_IT(&hlpuart1, (uint8_t*)&ch,1); return ch; } /* USER CODE END PV */ 因为板卡上带有ST-LINK，用的是USART2或LPUART1（二选一），所以把printf重定向到LPUART1串口。在IDE生成的代码中插入如下内容：首先，您需要在 main.c 文件中的 USER CODE Includes 中包含 “stdio.h” 以使用 printf。 /* USER CODE BEGIN Includes */ #include <stdio.h> /* USER CODE END Includes */ 以下代码将编译器将标准输出连接到 printf 的 UART。 /* Private variables ---------------------------------------------------------*/ UART_HandleTypeDef hlpuart1; /* USER CODE BEGIN PV */ #ifdef __GNUC__ #define PUTCHAR_PROTOTYPE int __io_putchar(int ch) #else #define PUTCHAR_PROTOTYPE int fputc(int ch, FILE *f) #endif PUTCHAR_PROTOTYPE { //同样USART2改为你的串口 HAL_UART_Transmit_IT(&hlpuart1, (uint8_t*)&ch,1); return ch; } /* USER CODE END PV */ 浮点数问题 RTC 配置RTC 开启低速晶振开启RTC 激活时钟和日历设置RTC 上图为每1秒触发一次中断设置中断配置时钟树编写代码在stm32u0xx_it.c 文件中找到RTC相关的函数寻早WakeUp的IRQ处理函数导航到此处函数 __weak void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc) 是可以重新实现的，在main.c 文件中重新定义此函数。 /* USER CODE BEGIN 0 */ void HAL_RTCEx_WakeUpTimerEventCallback(RTC_HandleTypeDef *hrtc){ //中断处理程序 } /* USER CODE END 0 */ 以上函数在RTC唤醒后打印当前的日期和时间 while中读取RTC /* USER CODE BEGIN WHILE */ RTC_TimeTypeDef sTime; RTC_DateTypeDef sDate; while (1) { HAL_RTC_GetTime(&hrtc, &sTime, RTC_FORMAT_BIN); HAL_RTC_GetDate(&hrtc, &sDate, RTC_FORMAT_BIN); printf(date_str,"%4d-%02d-%02d %02d:%02d:%02d\r\n",2000 + sDate.Year, sDate.Month, sDate.Date,sTime.Hours,sTime.Minutes,sTime.Seconds); } 转换时间戳 #include <time.h> /* USER CODE BEGIN PFP */ int32_t stm32_rtc_readtimestamp(const RTC_TimeTypeDef rTime,const RTC_DateTypeDef rDate){ struct tm tm_new; tm_new.tm_sec = rTime.Seconds; tm_new.tm_min=rTime.Minutes; tm_new.tm_hour=rTime.Hours - 8; tm_new.tm_mday=rDate.Date; tm_new.tm_mon=rDate.Month-1; tm_new.tm_year=rDate.Year+100; return mktime(&tm_new); } /* USER CODE END PFP */ int32_t timeStamp; while (1) { ...... timeStamp = stm32_rtc_readtimestamp(sTime,sDate); printf("timestamp = %ld",timeStamp); } 验证时间戳得到时间戳后，可以使用在线工具进行验证：时间戳(Unix timestamp)转换工具 - 在线工具。将我们自己的时间戳输入进去，即可得到北京时间，以此进行验证。也可以将我们需要转换的时间输入进去，转换得到时间戳。串口配置串口开启LPUART1，并修改针脚到PA2和PA3，这两个针脚可以直接通过开发板的Typec的虚拟串口访问。开启LPUART2，并修改针脚到PC0和PC1，这两个针脚用于和蓝牙模块通讯。开启串口中断按键输入开发板原理图按键配置驱动代码以下代码写入while中 HAL_GPIO_ReadPin(KEY_GPIO_Port, KEY_Pin); if(GPIO_PIN_RESET == HAL_GPIO_ReadPin(KEY_GPIO_Port, KEY_Pin)){ //是否为低电平，按下为低电平 HAL_Delay(10);//软件消抖 if(GPIO_PIN_RESET == HAL_GPIO_ReadPin(KEY_GPIO_Port, KEY_Pin)){ HAL_GPIO_TogglePin(LD4_GPIO_Port, LD4_Pin);//小灯翻转 while(HAL_GPIO_ReadPin(KEY_GPIO_Port, KEY_Pin) == GPIO_PIN_RESET){} } } 低功耗概述在利用RTC闹钟唤醒standby模式中，需要关注的问题有： 1.关于功耗控制，需要对不使用的IO口进行漏电流的控制，因此，最好将没有使用的IO口都配置为模拟输入状态。 2.利用RTC闹钟进行唤醒时，需要注意闹钟中断触发后，中断标识是否被清除，否则，standby模式很可能在进入后立马退出。 3.如果要在退出standby模式后，RTC时钟需要继续按照设定的时间计时，需要通过后备寄存器来判断单片机是否是第一次启动。三种模式电流功耗大小排序运行 > 睡眠 > 停止 > 待机。其中运行模式与睡眠模式功耗为mA级，停止模式与待机模式为uA级，其中待机最小可以达到<5uA。如何进入？睡眠模式：执行WFI或WFE指令可以使MCU进入睡眠状态。停止模式：在以下条件下执行WFI或WFE指令： 1、设置Cortex-M3系统控制寄存器中的SLEEPDEEP位； 2、清除电源控制寄存器(PWR_CR)中的PDDS位进入； 3、通过设置PWR_CR中LPDS位选择电压调节器的模式；待机模式：在以下条件下执行WFI或WFE指令： 1、设置Cortex-M3系统控制寄存器中的SLEEPDEEP位； 2、设置电源控制寄存器(PWR_CR)中的PDDS位； 3、清除电源控制/状态寄存器(PWR_CSR)中的WUF位；如何退出？睡眠模式：如果是执行WFI指令进入睡眠模式，任意一个外设中断都能将系统从睡眠模式唤醒。如果是执行WFE指令进入睡眠模式，一旦发生唤醒事件时，微处理器都将从睡眠模式退出。停止模式：如果是执行WFI进入停止模式，任一外部中断线为中断模式可以唤醒。如果是执行WFE进入停止模式。任一外部中断线为事件模式可以唤醒。待机模式：待机模式唤醒只有4种：外部复位、IWDG复位、WKUP引脚上的上升沿或RTC闹钟事件的上升沿。并且从待机唤醒后，除了电源控制/状态寄存器，所有寄存器被复位。唤醒后的代码执行等同于复位后的执行。 RTC唤醒设置在利用RTC闹钟唤醒standby模式中，需要关注的问题有： 1.关于功耗控制，需要对不使用的IO口进行漏电流的控制，因此，最好将没有使用的IO口都配置为模拟输入状态。参见针脚设置 2.利用RTC闹钟进行唤醒时，需要注意闹钟中断触发后，中断标识是否被清除，否则，standby模式很可能在进入后立马退出。 3.如果要在退出standby模式后，RTC时钟需要继续按照设定的时间计时，需要通过后备寄存器来判断单片机是否是第一次启动。进入待机模式 /* USER CODE BEGIN 0 */ void sys_enter_standby_mode(void) { GPIO_AnalogState_Config(); //禁用GPIO __HAL_RCC_PWR_CLK_ENABLE(); // 使能PWR时钟 HAL_PWR_EnableBkUpAccess(); HAL_PWR_EnterSTANDBYMode(); //进入待机模式 } /* USER CODE END 0 */ 避免RTC被重置 static void MX_RTC_Init(void) { ...... /* USER CODE BEGIN RTC_Init 1 */ HAL_PWR_EnableBkUpAccess(); /* USER CODE END RTC_Init 1 */ ...... ...... /* USER CODE BEGIN Check_RTC_BKUP */ if(HAL_RTCEx_BKUPRead(&hrtc,RTC_BKP_DR1) != 0xA5A5) //判断后备寄存器是否被赋值 { /* USER CODE END Check_RTC_BKUP */ /** Initialize RTC and set the Time and Date */ ...... ...... ...... /* USER CODE BEGIN RTC_Init 2 */ HAL_RTCEx_BKUPWrite(&hrtc, RTC_BKP_DR1, 0xA5A5); //这里就是将这个寄存器的标志设为刚才的那个值，下次掉电后就不会进入到这里来 } else { if (HAL_RTCEx_SetWakeUpTimer_IT(&hrtc, 0, RTC_WAKEUPCLOCK_CK_SPRE_16BITS, 0) != HAL_OK) { Error_Handler(); } /* RTC的中断配置初始化以及启动 */ } /* USER CODE END RTC_Init 2 */ } 设置IO口为模拟输入状态这个函数主要是为了在低功耗状态下，尽量控制IO上不必要的漏电流产生。在进入待机模式前调用。 /* USER CODE BEGIN 2 */ void GPIO_AnalogState_Config(void) { GPIO_InitTypeDef GPIO_InitStruct; /*Set all GPIO in analog state to reduce power consumption*/ __HAL_RCC_GPIOA_CLK_ENABLE(); __HAL_RCC_GPIOB_CLK_ENABLE(); __HAL_RCC_GPIOC_CLK_ENABLE(); GPIO_InitStruct.Mode = GPIO_MODE_ANALOG; GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_HIGH; GPIO_InitStruct.Pull = GPIO_NOPULL; GPIO_InitStruct.Pin = GPIO_PIN_All; HAL_GPIO_Init(GPIOA,&GPIO_InitStruct); HAL_GPIO_Init(GPIOB,&GPIO_InitStruct); HAL_GPIO_Init(GPIOC,&GPIO_InitStruct); __HAL_RCC_GPIOA_CLK_DISABLE(); __HAL_RCC_GPIOB_CLK_DISABLE(); __HAL_RCC_GPIOC_CLK_DISABLE(); } /* USER CODE END 2 */ Flash 编程上ST-LINKUtility 查看flash占用情况本器件地址为0x08000000 到 0x0803EED0 可以从0x08020000 开始进行写入。本MCU仅支持双位操作。 int d1 =0; int d2 =0; uint32_t flashwriteaddr = 0x08020000; //定义写入数据的地址 uint32_t pageError = 0; uint64_t flashwritedata = u32_to_u64(946657215,946658888);//0x386CD7BE00000002;//要写入的数据，必须得是双字64bit FLASH_EraseInitTypeDef flash_erase; //定义一个结构体变量，里面有擦除操作需要定义的变量 HAL_FLASH_Unlock(); //第二步：解锁 flash_erase.TypeErase = FLASH_TYPEERASE_PAGES; //擦除类型是“Page Erase” flash_erase.Page = 64; //擦除第16页 flash_erase.NbPages = 1; //一次性擦除2页,可以是任意页 HAL_FLASHEx_Erase(&flash_erase,&pageError); //第三步：参数写好后调用擦除函数 HAL_FLASH_Program(FLASH_TYPEPROGRAM_DOUBLEWORD, flashwriteaddr, flashwritedata);//第四步：写入数据 HAL_FLASH_Lock(); //第五步：上锁 d1 = *(__IO uint32_t *)flashwriteaddr; //读出flash中的数据 d2 = *(__IO uint32_t *)(flashwriteaddr+4); //地址偏移+4 printf("read data:%d %d\r\n",d2,d1); HAL_Delay(200); /** * 通过位操作实现2个uint32_t合并为uint64_t */ uint64_t u32_to_u64(uint32_t d1,uint32_t d2){ //先将uint32_t的a转为uint64_t，此时a前面32位都是0，然后左移32位，此时右32位为0，最后加上uint32_t类型的b，填充右32位的0 return (uint64_t)(((uint64_t)d1) << 32) + d2; } 分页以下是开发板载的mcu的分页表。 //STM32u0的FLASH大小为256KB，只有128个页 #define ADDR_FLASH_PAGE_0 ((uint32_t)0x08000000) /* Base @ of Page 0, 2 Kbytes */ #define ADDR_FLASH_PAGE_1 ((uint32_t)0x08000800) /* Base @ of Page 1, 2 Kbytes */ #define ADDR_FLASH_PAGE_2 ((uint32_t)0x08001000) /* Base @ of Page 2, 2 Kbytes */ #define ADDR_FLASH_PAGE_3 ((uint32_t)0x08001800) /* Base @ of Page 3, 2 Kbytes */ #define ADDR_FLASH_PAGE_4 ((uint32_t)0x08002000) /* Base @ of Page 4, 2 Kbytes */ #define ADDR_FLASH_PAGE_5 ((uint32_t)0x08002800) /* Base @ of Page 5, 2 Kbytes */ #define ADDR_FLASH_PAGE_6 ((uint32_t)0x08003000) /* Base @ of Page 6, 2 Kbytes */ #define ADDR_FLASH_PAGE_7 ((uint32_t)0x08003800) /* Base @ of Page 7, 2 Kbytes */ #define ADDR_FLASH_PAGE_8 ((uint32_t)0x08004000) /* Base @ of Page 8, 2 Kbytes */ #define ADDR_FLASH_PAGE_9 ((uint32_t)0x08004800) /* Base @ of Page 9, 2 Kbytes */ #define ADDR_FLASH_PAGE_10 ((uint32_t)0x08005000) /* Base @ of Page 10, 2 Kbytes */ #define ADDR_FLASH_PAGE_11 ((uint32_t)0x08005800) /* Base @ of Page 11, 2 Kbytes */ #define ADDR_FLASH_PAGE_12 ((uint32_t)0x08006000) /* Base @ of Page 12, 2 Kbytes */ #define ADDR_FLASH_PAGE_13 ((uint32_t)0x08006800) /* Base @ of Page 13, 2 Kbytes */ #define ADDR_FLASH_PAGE_14 ((uint32_t)0x08007000) /* Base @ of Page 14, 2 Kbytes */ #define ADDR_FLASH_PAGE_15 ((uint32_t)0x08007800) /* Base @ of Page 15, 2 Kbytes */ #define ADDR_FLASH_PAGE_16 ((uint32_t)0x08008000) /* Base @ of Page 16, 2 Kbytes */ #define ADDR_FLASH_PAGE_17 ((uint32_t)0x08008800) /* Base @ of Page 17, 2 Kbytes */ #define ADDR_FLASH_PAGE_18 ((uint32_t)0x08009000) /* Base @ of Page 18, 2 Kbytes */ #define ADDR_FLASH_PAGE_19 ((uint32_t)0x08009800) /* Base @ of Page 19, 2 Kbytes */ #define ADDR_FLASH_PAGE_20 ((uint32_t)0x0800A000) /* Base @ of Page 20, 2 Kbytes */ #define ADDR_FLASH_PAGE_21 ((uint32_t)0x0800A800) /* Base @ of Page 21, 2 Kbytes */ #define ADDR_FLASH_PAGE_22 ((uint32_t)0x0800B000) /* Base @ of Page 22, 2 Kbytes */ #define ADDR_FLASH_PAGE_23 ((uint32_t)0x0800B800) /* Base @ of Page 23, 2 Kbytes */ #define ADDR_FLASH_PAGE_24 ((uint32_t)0x0800C000) /* Base @ of Page 24, 2 Kbytes */ #define ADDR_FLASH_PAGE_25 ((uint32_t)0x0800C800) /* Base @ of Page 25, 2 Kbytes */ #define ADDR_FLASH_PAGE_26 ((uint32_t)0x0800D000) /* Base @ of Page 26, 2 Kbytes */ #define ADDR_FLASH_PAGE_27 ((uint32_t)0x0800D800) /* Base @ of Page 27, 2 Kbytes */ #define ADDR_FLASH_PAGE_28 ((uint32_t)0x0800E000) /* Base @ of Page 28, 2 Kbytes */ #define ADDR_FLASH_PAGE_29 ((uint32_t)0x0800E800) /* Base @ of Page 29, 2 Kbytes */ #define ADDR_FLASH_PAGE_30 ((uint32_t)0x0800F000) /* Base @ of Page 30, 2 Kbytes */ #define ADDR_FLASH_PAGE_31 ((uint32_t)0x0800F800) /* Base @ of Page 31, 2 Kbytes */ #define ADDR_FLASH_PAGE_32 ((uint32_t)0x08010000) /* Base @ of Page 32, 2 Kbytes */ #define ADDR_FLASH_PAGE_33 ((uint32_t)0x08010800) /* Base @ of Page 33, 2 Kbytes */ #define ADDR_FLASH_PAGE_34 ((uint32_t)0x08011000) /* Base @ of Page 34, 2 Kbytes */ #define ADDR_FLASH_PAGE_35 ((uint32_t)0x08011800) /* Base @ of Page 35, 2 Kbytes */ #define ADDR_FLASH_PAGE_36 ((uint32_t)0x08012000) /* Base @ of Page 36, 2 Kbytes */ #define ADDR_FLASH_PAGE_37 ((uint32_t)0x08012800) /* Base @ of Page 37, 2 Kbytes */ #define ADDR_FLASH_PAGE_38 ((uint32_t)0x08013000) /* Base @ of Page 38, 2 Kbytes */ #define ADDR_FLASH_PAGE_39 ((uint32_t)0x08013800) /* Base @ of Page 39, 2 Kbytes */ #define ADDR_FLASH_PAGE_40 ((uint32_t)0x08014000) /* Base @ of Page 40, 2 Kbytes */ #define ADDR_FLASH_PAGE_41 ((uint32_t)0x08014800) /* Base @ of Page 41, 2 Kbytes */ #define ADDR_FLASH_PAGE_42 ((uint32_t)0x08015000) /* Base @ of Page 42, 2 Kbytes */ #define ADDR_FLASH_PAGE_43 ((uint32_t)0x08015800) /* Base @ of Page 43, 2 Kbytes */ #define ADDR_FLASH_PAGE_44 ((uint32_t)0x08016000) /* Base @ of Page 44, 2 Kbytes */ #define ADDR_FLASH_PAGE_45 ((uint32_t)0x08016800) /* Base @ of Page 45, 2 Kbytes */ #define ADDR_FLASH_PAGE_46 ((uint32_t)0x08017000) /* Base @ of Page 46, 2 Kbytes */ #define ADDR_FLASH_PAGE_47 ((uint32_t)0x08017800) /* Base @ of Page 47, 2 Kbytes */ #define ADDR_FLASH_PAGE_48 ((uint32_t)0x08018000) /* Base @ of Page 48, 2 Kbytes */ #define ADDR_FLASH_PAGE_49 ((uint32_t)0x08018800) /* Base @ of Page 49, 2 Kbytes */ #define ADDR_FLASH_PAGE_50 ((uint32_t)0x08019000) /* Base @ of Page 50, 2 Kbytes */ #define ADDR_FLASH_PAGE_51 ((uint32_t)0x08019800) /* Base @ of Page 51, 2 Kbytes */ #define ADDR_FLASH_PAGE_52 ((uint32_t)0x0801A000) /* Base @ of Page 52, 2 Kbytes */ #define ADDR_FLASH_PAGE_53 ((uint32_t)0x0801A800) /* Base @ of Page 53, 2 Kbytes */ #define ADDR_FLASH_PAGE_54 ((uint32_t)0x0801B000) /* Base @ of Page 54, 2 Kbytes */ #define ADDR_FLASH_PAGE_55 ((uint32_t)0x0801B800) /* Base @ of Page 55, 2 Kbytes */ #define ADDR_FLASH_PAGE_56 ((uint32_t)0x0801C000) /* Base @ of Page 56, 2 Kbytes */ #define ADDR_FLASH_PAGE_57 ((uint32_t)0x0801C800) /* Base @ of Page 57, 2 Kbytes */ #define ADDR_FLASH_PAGE_58 ((uint32_t)0x0801D000) /* Base @ of Page 58, 2 Kbytes */ #define ADDR_FLASH_PAGE_59 ((uint32_t)0x0801D800) /* Base @ of Page 59, 2 Kbytes */ #define ADDR_FLASH_PAGE_60 ((uint32_t)0x0801E000) /* Base @ of Page 60, 2 Kbytes */ #define ADDR_FLASH_PAGE_61 ((uint32_t)0x0801E800) /* Base @ of Page 61, 2 Kbytes */ #define ADDR_FLASH_PAGE_62 ((uint32_t)0x0801F000) /* Base @ of Page 62, 2 Kbytes */ #define ADDR_FLASH_PAGE_63 ((uint32_t)0x0801F800) /* Base @ of Page 63, 2 Kbytes */ #define ADDR_FLASH_PAGE_64 ((uint32_t)0x08020000) /* Base @ of Page 64, 2 Kbytes */ #define ADDR_FLASH_PAGE_65 ((uint32_t)0x08020800) /* Base @ of Page 65, 2 Kbytes */ #define ADDR_FLASH_PAGE_66 ((uint32_t)0x08021000) /* Base @ of Page 66, 2 Kbytes */ #define ADDR_FLASH_PAGE_67 ((uint32_t)0x08021800) /* Base @ of Page 67, 2 Kbytes */ #define ADDR_FLASH_PAGE_68 ((uint32_t)0x08022000) /* Base @ of Page 68, 2 Kbytes */ #define ADDR_FLASH_PAGE_69 ((uint32_t)0x08022800) /* Base @ of Page 69, 2 Kbytes */ #define ADDR_FLASH_PAGE_70 ((uint32_t)0x08023000) /* Base @ of Page 70, 2 Kbytes */ #define ADDR_FLASH_PAGE_71 ((uint32_t)0x08023800) /* Base @ of Page 71, 2 Kbytes */ #define ADDR_FLASH_PAGE_72 ((uint32_t)0x08024000) /* Base @ of Page 72, 2 Kbytes */ #define ADDR_FLASH_PAGE_73 ((uint32_t)0x08024800) /* Base @ of Page 73, 2 Kbytes */ #define ADDR_FLASH_PAGE_74 ((uint32_t)0x08025000) /* Base @ of Page 74, 2 Kbytes */ #define ADDR_FLASH_PAGE_75 ((uint32_t)0x08025800) /* Base @ of Page 75, 2 Kbytes */ #define ADDR_FLASH_PAGE_76 ((uint32_t)0x08026000) /* Base @ of Page 76, 2 Kbytes */ #define ADDR_FLASH_PAGE_77 ((uint32_t)0x08026800) /* Base @ of Page 77, 2 Kbytes */ #define ADDR_FLASH_PAGE_78 ((uint32_t)0x08027000) /* Base @ of Page 78, 2 Kbytes */ #define ADDR_FLASH_PAGE_79 ((uint32_t)0x08027800) /* Base @ of Page 79, 2 Kbytes */ #define ADDR_FLASH_PAGE_80 ((uint32_t)0x08028000) /* Base @ of Page 80, 2 Kbytes */ #define ADDR_FLASH_PAGE_81 ((uint32_t)0x08028800) /* Base @ of Page 81, 2 Kbytes */ #define ADDR_FLASH_PAGE_82 ((uint32_t)0x08029000) /* Base @ of Page 82, 2 Kbytes */ #define ADDR_FLASH_PAGE_83 ((uint32_t)0x08029800) /* Base @ of Page 83, 2 Kbytes */ #define ADDR_FLASH_PAGE_84 ((uint32_t)0x0802A000) /* Base @ of Page 84, 2 Kbytes */ #define ADDR_FLASH_PAGE_85 ((uint32_t)0x0802A800) /* Base @ of Page 85, 2 Kbytes */ #define ADDR_FLASH_PAGE_86 ((uint32_t)0x0802B000) /* Base @ of Page 86, 2 Kbytes */ #define ADDR_FLASH_PAGE_87 ((uint32_t)0x0802B800) /* Base @ of Page 87, 2 Kbytes */ #define ADDR_FLASH_PAGE_88 ((uint32_t)0x0802C000) /* Base @ of Page 88, 2 Kbytes */ #define ADDR_FLASH_PAGE_89 ((uint32_t)0x0802C800) /* Base @ of Page 89, 2 Kbytes */ #define ADDR_FLASH_PAGE_90 ((uint32_t)0x0802D000) /* Base @ of Page 90, 2 Kbytes */ #define ADDR_FLASH_PAGE_91 ((uint32_t)0x0802D800) /* Base @ of Page 91, 2 Kbytes */ #define ADDR_FLASH_PAGE_92 ((uint32_t)0x0802E000) /* Base @ of Page 92, 2 Kbytes */ #define ADDR_FLASH_PAGE_93 ((uint32_t)0x0802E800) /* Base @ of Page 93, 2 Kbytes */ #define ADDR_FLASH_PAGE_94 ((uint32_t)0x0802F000) /* Base @ of Page 94, 2 Kbytes */ #define ADDR_FLASH_PAGE_95 ((uint32_t)0x0802F800) /* Base @ of Page 95, 2 Kbytes */ #define ADDR_FLASH_PAGE_96 ((uint32_t)0x08030000) /* Base @ of Page 96, 2 Kbytes */ #define ADDR_FLASH_PAGE_97 ((uint32_t)0x08030800) /* Base @ of Page 97, 2 Kbytes */ #define ADDR_FLASH_PAGE_98 ((uint32_t)0x08031000) /* Base @ of Page 98, 2 Kbytes */ #define ADDR_FLASH_PAGE_99 ((uint32_t)0x08031800) /* Base @ of Page 99, 2 Kbytes */ #define ADDR_FLASH_PAGE_100 ((uint32_t)0x08032000) /* Base @ of Page 100, 2 Kbytes */ #define ADDR_FLASH_PAGE_101 ((uint32_t)0x08032800) /* Base @ of Page 101, 2 Kbytes */ #define ADDR_FLASH_PAGE_102 ((uint32_t)0x08033000) /* Base @ of Page 102, 2 Kbytes */ #define ADDR_FLASH_PAGE_103 ((uint32_t)0x08033800) /* Base @ of Page 103, 2 Kbytes */ #define ADDR_FLASH_PAGE_104 ((uint32_t)0x08034000) /* Base @ of Page 104, 2 Kbytes */ #define ADDR_FLASH_PAGE_105 ((uint32_t)0x08034800) /* Base @ of Page 105, 2 Kbytes */ #define ADDR_FLASH_PAGE_106 ((uint32_t)0x08035000) /* Base @ of Page 106, 2 Kbytes */ #define ADDR_FLASH_PAGE_107 ((uint32_t)0x08035800) /* Base @ of Page 107, 2 Kbytes */ #define ADDR_FLASH_PAGE_108 ((uint32_t)0x08036000) /* Base @ of Page 108, 2 Kbytes */ #define ADDR_FLASH_PAGE_109 ((uint32_t)0x08036800) /* Base @ of Page 109, 2 Kbytes */ #define ADDR_FLASH_PAGE_110 ((uint32_t)0x08037000) /* Base @ of Page 110, 2 Kbytes */ #define ADDR_FLASH_PAGE_111 ((uint32_t)0x08037800) /* Base @ of Page 111, 2 Kbytes */ #define ADDR_FLASH_PAGE_112 ((uint32_t)0x08038000) /* Base @ of Page 112, 2 Kbytes */ #define ADDR_FLASH_PAGE_113 ((uint32_t)0x08038800) /* Base @ of Page 113, 2 Kbytes */ #define ADDR_FLASH_PAGE_114 ((uint32_t)0x08039000) /* Base @ of Page 114, 2 Kbytes */ #define ADDR_FLASH_PAGE_115 ((uint32_t)0x08039800) /* Base @ of Page 115, 2 Kbytes */ #define ADDR_FLASH_PAGE_116 ((uint32_t)0x0803A000) /* Base @ of Page 116, 2 Kbytes */ #define ADDR_FLASH_PAGE_117 ((uint32_t)0x0803A800) /* Base @ of Page 117, 2 Kbytes */ #define ADDR_FLASH_PAGE_118 ((uint32_t)0x0803B000) /* Base @ of Page 118, 2 Kbytes */ #define ADDR_FLASH_PAGE_119 ((uint32_t)0x0803B800) /* Base @ of Page 119, 2 Kbytes */ #define ADDR_FLASH_PAGE_120 ((uint32_t)0x0803C000) /* Base @ of Page 120, 2 Kbytes */ #define ADDR_FLASH_PAGE_121 ((uint32_t)0x0803C800) /* Base @ of Page 121, 2 Kbytes */ #define ADDR_FLASH_PAGE_122 ((uint32_t)0x0803D000) /* Base @ of Page 122, 2 Kbytes */ #define ADDR_FLASH_PAGE_123 ((uint32_t)0x0803D800) /* Base @ of Page 123, 2 Kbytes */ #define ADDR_FLASH_PAGE_124 ((uint32_t)0x0803E000) /* Base @ of Page 124, 2 Kbytes */ #define ADDR_FLASH_PAGE_125 ((uint32_t)0x0803E800) /* Base @ of Page 125, 2 Kbytes */ #define ADDR_FLASH_PAGE_126 ((uint32_t)0x0803F000) /* Base @ of Page 126, 2 Kbytes */ #define ADDR_FLASH_PAGE_127 ((uint32_t)0x0803F800) /* Base @ of Page 127, 2 Kbytes */
2024-04-16
回复了主题帖：测评入围名单： ST NUCLEO-U083RC（ST官方新品测评任务等你玩），追加1块

个人信息无误，确认可以完成测评分享计划